コンソール出せるようになるまで散々手こずったのを解決して色々頑張った記念
General initialization - Version: 1.0.0
Detected Device ID 6810
High speed PHY - Version: 2.0
Init Customer board board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 5 | PCIe0 |
| 5 | 5 | PCIe2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: remains Gen1
:** Link is Gen1, check the EP capability
PCIe, Idx 2: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.39.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
SA-W2 IPL Monitor version 1.20
Copyright 2003-2016 Internet Initiative Japan Inc.
boot: Boot from Flash...
Reading FLASH. Done.
Firmware checksum is correct.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.92 (musashino205@TAIHA.NET) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.2.0 r21272+750-b97e5ac785) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 SMP Sat Feb 11 07:41:35 2023
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: IIJ SA-W2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14028 r8192 d22836 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8
[ 0.000000] Bootloader command line not present
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246328K/262144K available (8192K kernel code, 631K rwdata, 1884K rodata, 1024K init, 232K bss, 15816K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 ->0x16070000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000001] sched_clock: 64 bits at 533MHz, resolution 1ns, wraps every 2199023255551ns
[ 0.000022] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x7aed16d152, max_idle_ns: 440795225656 ns
[ 0.000043] Switching to timer-based delay loop, resolution 1ns
[ 0.000215] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000224] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000445] Calibrating delay loop (skipped), value calculated using timer frequency.. 1066.00 BogoMIPS (lpj=5330000)
[ 0.000458] pid_max: default: 32768 minimum: 301
[ 0.000578] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000590] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001095] CPU: Testing write buffer coherency: ok
[ 0.001115] CPU0: Spectre v2: using BPIALL workaround
[ 0.001237] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001659] Setting up static identity map for 0x100000 - 0x100060
[ 0.001762] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4
[ 0.001869] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001956] rcu: Hierarchical SRCU implementation.
[ 0.002062] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.002123] smp: Bringing up secondary CPUs ...
[ 0.002129] smp: Brought up 1 node, 1 CPU
[ 0.002136] SMP: Total of 1 processors activated (1066.00 BogoMIPS).
[ 0.002144] CPU: All CPU(s) started in SVC mode.
[ 0.004466] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.004533] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.004548] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[ 0.004618] pinctrl core: initialized pinctrl subsystem
[ 0.005311] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.005925] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.006484] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006542] cpuidle: using governor ladder
[ 0.006700] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.006709] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.016828] cryptd: max_cpu_qlen set to 1000
[ 0.018375] SCSI subsystem initialized
[ 0.018594] usbcore: registered new interface driver usbfs
[ 0.018624] usbcore: registered new interface driver hub
[ 0.018647] usbcore: registered new device driver usb
[ 0.019384] clocksource: Switched to clocksource arm_global_timer
[ 0.019853] NET: Registered PF_INET protocol family
[ 0.019961] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.020344] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.020373] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.020384] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.020404] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.020434] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.020476] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.020500] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.020624] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.020648] PCI: CLS 0 bytes, default 64
[ 0.022327] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.025061] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.025069] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.027235] armada-38x-pinctrl d0018000.pinctrl: registered pinctrl driver
[ 0.027748] gpio-2 (usb-hub-reset): hogged as output/high
[ 0.027866] debugfs: Directory 'd0018100.gpio' with parent 'regmap' already present!
[ 0.028192] debugfs: Directory 'd0018140.gpio' with parent 'regmap' already present!
[ 0.028515] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges:
[ 0.028549] mvebu-pcie soc:pcie: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000
[ 0.028572] mvebu-pcie soc:pcie: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000
[ 0.028592] mvebu-pcie soc:pcie: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000
[ 0.028610] mvebu-pcie soc:pcie: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000
[ 0.028628] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.028646] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.028663] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.028679] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.028696] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.028709] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.028867] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 0.028878] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.028890] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff])
[ 0.028900] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff])
[ 0.028909] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff])
[ 0.028918] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff])
[ 0.028927] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.028934] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.029028] pci 0000:00:01.0: [11ab:6810] type 01 class 0x060400
[ 0.029279] pci 0000:00:03.0: [11ab:6810] type 01 class 0x060400
[ 0.030432] PCI: bus0: Fast back to back transfers disabled
[ 0.030443] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.030456] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.030552] pci 0000:01:00.0: [168c:002e] type 00 class 0x028000
[ 0.030578] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 0.030687] pci 0000:01:00.0: supports D1
[ 0.030695] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.031889] PCI: bus1: Fast back to back transfers disabled
[ 0.031899] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.031988] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000
[ 0.032013] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.032047] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.032125] pci 0000:02:00.0: supports D1
[ 0.032132] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[ 0.033319] PCI: bus2: Fast back to back transfers disabled
[ 0.033329] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.033370] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[ 0.033383] pci 0000:00:03.0: BAR 8: assigned [mem 0xe0200000-0xe04fffff]
[ 0.033394] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 0.033410] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.033420] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 0.033439] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe03fffff 64bit]
[ 0.033455] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0400000-0xe040ffff pref]
[ 0.033464] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 0.033473] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe04fffff]
[ 0.033805] mv_xor d0060800.xor: Marvell shared XOR driver
[ 0.099963] mv_xor d0060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.100144] mv_xor d0060900.xor: Marvell shared XOR driver
[ 0.159958] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.160176] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.160558] printk: console [ttyS0] disabled
[ 0.180673] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 29, base_baud = 15625000) is a 16550A
[ 1.131419] printk: console [ttyS0] enabled
[ 1.139287] loop: module loaded
[ 1.147087] spi-nor spi1.0: w25q256 (32768 Kbytes)
[ 1.152239] 5 fixed-partitions partitions found on MTD device spi1.0
[ 1.158636] OF: Bad cell count for /soc/spi@10680/flash@0/partitions
[ 1.165067] OF: Bad cell count for /soc/spi@10680/flash@0/partitions
[ 1.171679] OF: Bad cell count for /soc/spi@10680/flash@0/partitions
[ 1.178073] OF: Bad cell count for /soc/spi@10680/flash@0/partitions
[ 1.184554] Creating 5 MTD partitions on "spi1.0":
[ 1.189364] 0x000000000000-0x000000100000 : "bootloader"
[ 1.195773] 0x000000100000-0x000000110000 : "bootloader-env"
[ 1.201817] 0x000000110000-0x000000200000 : "board_info"
[ 1.207838] 0x000000200000-0x000001100000 : "firmware"
[ 1.213944] 2 seil-fw partitions found on MTD device firmware
[ 1.219740] Creating 2 MTD partitions on "firmware":
[ 1.224723] 0x000000000000-0x000000370000 : "kernel"
[ 1.230260] 0x000000370000-0x000000f00000 : "rootfs"
[ 1.235531] mtd: setting mtd5 (rootfs) as root device
[ 1.240947] 1 squashfs-split partitions found on MTD device rootfs
[ 1.247152] 0x000000800000-0x000000f00000 : "rootfs_data"
[ 1.252952] 0x000001100000-0x000002000000 : "rescue"
[ 1.265188] mv88e6085 d0072004.mdio-mii:00: switch 0x1720 detected: Marvell 88E6172, revision 1
[ 1.443907] mvneta_bm d00c8000.bm: Buffer Manager for network controller enabled
[ 1.454326] mvneta d0070000.ethernet eth0: Using device tree mac address 00:e0:4d:3c:b7:18
[ 1.462841] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.469405] ehci-platform: EHCI generic platform driver
[ 1.474747] ehci-orion: EHCI orion driver
[ 1.478926] orion-ehci d0058000.usb: EHCI Host Controller
[ 1.484369] orion-ehci d0058000.usb: new USB bus registered, assigned bus number 1
[ 1.492027] orion-ehci d0058000.usb: irq 45, io mem 0xd0058000
[ 1.519431] orion-ehci d0058000.usb: USB 2.0 started, EHCI 1.00
[ 1.525752] hub 1-0:1.0: USB hub found
[ 1.529746] hub 1-0:1.0: 1 port detected
[ 1.534267] usbcore: registered new interface driver usb-storage
[ 1.540841] armada38x-rtc d00a3800.rtc: registered as rtc0
[ 1.546421] armada38x-rtc d00a3800.rtc: setting system clock to 2003-08-17T08:39:27 UTC (1061109567)
[ 1.555777] i2c_dev: i2c /dev entries driver
[ 1.562692] orion_wdt: Initial timeout 171 sec
[ 1.567436] sdhci: Secure Digital Host Controller Interface driver
[ 1.573674] sdhci: Copyright(c) Pierre Ossman
[ 1.578170] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.589004] marvell-cesa d0090000.crypto: CESA device successfully registered
[ 1.596809] NET: Registered PF_INET6 protocol family
[ 1.603097] Segment Routing with IPv6
[ 1.606809] In-situ OAM (IOAM) with IPv6
[ 1.610835] NET: Registered PF_PACKET protocol family
[ 1.616270] 8021q: 802.1Q VLAN Support v1.8
[ 1.620542] Registering SWP/SWPB emulation handler
[ 1.629518] mv88e6085 d0072004.mdio-mii:00: switch 0x1720 detected: Marvell 88E6172, revision 1
[ 1.819390] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.020176] hub 1-1:1.0: USB hub found
[ 2.024130] hub 1-1:1.0: 2 ports detected
[ 2.085576] mv88e6085 d0072004.mdio-mii:00: configuring for fixed/rgmii-id link mode
[ 2.096704] mv88e6085 d0072004.mdio-mii:00: Link is Up - 1Gbps/Full - flow control off
[ 2.197108] mv88e6085 d0072004.mdio-mii:00 ge1_0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=62)
[ 2.311352] mv88e6085 d0072004.mdio-mii:00 ge1_1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=63)
[ 2.419169] mv88e6085 d0072004.mdio-mii:00 ge1_2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=64)
[ 2.531349] mv88e6085 d0072004.mdio-mii:00 ge1_3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=65)
[ 2.639227] mv88e6085 d0072004.mdio-mii:00 ge0 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=66)
[ 2.653419] DSA: tree 0 setup
[ 2.680484] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.688365] Freeing unused kernel image (initmem) memory: 1024K
[ 2.694575] Run /sbin/init as init process
[ 3.567347] init: Console is alive
[ 3.570927] init: - watchdog -
[ 5.646326] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.743371] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.753290] init: - preinit -
[ 7.835269] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.945738] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.965435] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.751669] mvneta d0070000.ethernet eth0: configuring for fixed/rgmii link mode
[ 8.759699] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 8.767585] mv88e6085 d0072004.mdio-mii:00 ge1_0: configuring for phy/gmii link mode
[ 8.777979] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.980081] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 11.002544] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.122461] procd: - early -
[ 11.125424] procd: - watchdog -
[ 11.764857] procd: - watchdog -
[ 11.768237] procd: - ubus -
[ 11.876687] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.883810] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.975926] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.984184] procd: - init -
Please press Enter to activate this console.
[ 12.912244] random: jshn: uninitialized urandom read (4 bytes read)
[ 12.936750] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.949554] random: ubus: uninitialized urandom read (4 bytes read)
[ 12.988966] urngd: v1.0.2 started.
[ 13.044494] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.157079] random: crng init done
[ 13.160530] random: 25 urandom warning(s) missed due to ratelimiting
[ 13.252877] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
[ 13.260508] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
[ 13.687146] PPP generic driver version 2.4.2
[ 13.692933] NET: Registered PF_PPPOX protocol family
[ 13.707289] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 13.715488] pci 0000:00:03.0: enabling device (0140 -> 0142)
[ 13.721222] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 13.727733] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 14.103519] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 14.112845] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.122764] ath10k_pci 0000:02:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 14.172961] ath10k_pci 0000:02:00.0: Loading BDF type 0
[ 14.419606] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 15.279325] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 15.296045] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
[ 15.302123] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 15.310165] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 15.373658] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 15.383377] ath10k_pci 0000:02:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 15.532803] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 15.538503] ath9k 0000:01:00.0: enabling device (0140 -> 0142)
[ 15.644808] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xd0c80000, irq=81
[ 15.654475] ath10k_pci 0000:02:00.0: DFS region 0x0 not supported, will trigger radar for every pulse
[ 15.999865] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 33.774300] mvneta d0070000.ethernet eth0: Link is Down
[ 33.795897] mvneta d0070000.ethernet eth0: configuring for fixed/rgmii link mode
[ 33.803677] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 33.826372] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.848491] mv88e6085 d0072004.mdio-mii:00 ge1_0: configuring for phy/gmii link mode
[ 33.879970] br-lan: port 1(ge1_0) entered blocking state
[ 33.885324] br-lan: port 1(ge1_0) entered disabled state
[ 33.932226] device ge1_0 entered promiscuous mode
[ 33.936961] device eth0 entered promiscuous mode
[ 34.069910] mv88e6085 d0072004.mdio-mii:00 ge1_1: configuring for phy/gmii link mode
[ 34.099026] br-lan: port 2(ge1_1) entered blocking state
[ 34.104412] br-lan: port 2(ge1_1) entered disabled state
[ 34.176390] device ge1_1 entered promiscuous mode
[ 34.188374] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 34.215252] jffs2_build_filesystem(): unlocking the mtd device...
[ 34.215262] done.
[ 34.223434] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 34.226063] mv88e6085 d0072004.mdio-mii:00 ge1_2: configuring for phy/gmii link mode
[ 34.318906] br-lan: port 3(ge1_2) entered blocking state
[ 34.324286] br-lan: port 3(ge1_2) entered disabled state
[ 34.369661] device ge1_2 entered promiscuous mode
[ 34.388467] mv88e6085 d0072004.mdio-mii:00 ge1_3: configuring for phy/gmii link mode
[ 34.536144] br-lan: port 4(ge1_3) entered blocking state
[ 34.541535] br-lan: port 4(ge1_3) entered disabled state
[ 34.604326] device ge1_3 entered promiscuous mode
[ 34.639419] mv88e6085 d0072004.mdio-mii:00 ge0: configuring for phy/gmii link mode
[ 38.135669] mv88e6085 d0072004.mdio-mii:00 ge0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 38.144192] IPv6: ADDRCONF(NETDEV_CHANGE): ge0: link becomes ready
[ 63.117643] done.
[ 63.119596] jffs2: notice: (2257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 63.272817] overlayfs: upper fs does not support tmpfile.
BusyBox v1.36.0 (2023-02-11 07:41:35 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r22041+7-b932285141
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ubus call system board
{
"kernel": "5.15.92",
"hostname": "OpenWrt",
"system": "ARMv7 Processor rev 1 (v7l)",
"model": "IIJ SA-W2",
"board_name": "iij,sa-w2",
"rootfs_type": "squashfs",
"release": {
"distribution": "OpenWrt",
"version": "SNAPSHOT",
"revision": "r22041+7-b932285141",
"target": "mvebu/cortexa9",
"description": "OpenWrt SNAPSHOT r22041+7-b932285141"
}
}
root@OpenWrt:/#
