大破雑記帳

個人用メモな雑記ブログ　いろんなことをざっくりと。

WN-DX2033GR

Router/I-O DATA

発売に前後してファームウェアから調べた際、MT7621搭載機であることを確認していたもの。
某氏から提供して頂いたものの、しばらく多忙であったこと、Realtek SoCのスイッチングハブ等に注力してしまっていたことから後回しになっていたが、ようやく多少落ち着いてきたので着手する。
サポートの為弄っていくのでメモ。

Switch

zone WAN LAN
port (WN-DX2033GR) インターネット （LAN番号刻印無し）
port (MT7530) port0 port1 port2 port3 port4

MAC

  • LAN: 50:41:B9:xx:xx:90 (Ubootenv, ethaddr (text) / Factory, 0xE000 (hex))
  • WAN: 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
  • 2.4G: 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
  • 5G: 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))

U-Boot

WN-AX2033GRの情報を参考に強引にKernelへログインしたうえでブート時のmtdロックを回避、
sys debugflag 1
を設定してデバッグモードを有効化しZ-Loaderを停止できるように変更。再度ブート時にZ-Loaderに入り、
ATGU
でU-Bootへ移動する

  • help

      MSTC # help
  Unknown command 'help' - try 'help'

  • version

      MSTC # version
  Unknown command 'version' - try 'help'

  • printenv

      MSTC # printenv
  bootcmd=tftp
  ipaddr=10.10.10.123
  serverip=10.10.10.3
  serialnum=xxxxxxxxxxxx
  countrycode=EA
  ethaddr=50:41:B9:xx:xx:90
  nfLicense=xxxxxxxxxxxx
  wifi1ssid1=IODATA-xxxx90-2G
  wifi1ssid2=IO-Guest-xxxx90-2G
  wifi2ssid1=IODATA-xxxx90-5G
  wifiwpapsk=xxxxxxxxxxxxx
  wifiwpspin=xxxxxxxx
  wifi2ssid2=IO-Guest-xxxx90-5G
  stdin=serial
  stdout=serial
  stderr=serial
  ethact=Eth0 (10/100-M)

  Environment size: 365/131068 bytes

  • tftp

      MSTC # tftp

  NetTxPacket = 0x87FE2FC0

  KSEG1ADDR(NetTxPacket) = 0xA7FE2FC0

  NetLoop,call eth_halt !

  NetLoop,call eth_init !
  Trying Eth0 (10/100-M)

  Waitting for RX_DMA_BUSY status Start... done

  dev->iobase=BE100000,GDMA1_MAC_ADRH=0000FD9B

  dev->iobase=BE100000,GDMA1_MAC_ADRL=FFFFFFFF

  ETH_STATE_ACTIVE!!
  *** Warning: no boot file name; using 'test.bin'
  Using Eth0 (10/100-M) device
  TFTP from server 10.10.10.3; our IP address is 10.10.10.123
  Filename 'test.bin'.

  TIMEOUT_COUNT=10,Load address: 0x80200000
  Loading: checksum bad
  checksum bad
  checksum bad
  checksum bad

Kernel

パスワードが設定されている

  • uname -a

      root@WN-DX2033GR:~# uname -a
  Linux WN-DX2033GR 3.10.14 #1 SMP Thu Sep 3 17:22:37 CST 2020 mips GNU/Linux

  • cat /proc/version

      root@WN-DX2033GR:~# cat /proc/version
  Linux version 3.10.14 (*******@*******-PC-*******-******) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Thu Sep 3 17:22:37 CST 2020

  • cat /proc/cpuinfo

      root@WN-DX2033GR:~# cat /proc/cpuinfo
  system type             : MT7621
  machine                 : Unknown
  processor               : 0
  cpu model               : MIPS 1004Kc V2.15
  BogoMIPS                : 583.68
  wait instruction        : yes
  microsecond timers      : yes
  tlb_entries             : 32
  extra interrupt vector  : yes
  hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
  isa                     : mips1 mips2 mips32r1 mips32r2
  ASEs implemented        : mips16 dsp mt
  shadow register sets    : 1
  kscratch registers      : 0
  core                    : 0
  VPE                     : 0
  VCED exceptions         : not available
  VCEI exceptions         : not available

  processor               : 1
  cpu model               : MIPS 1004Kc V2.15
  BogoMIPS                : 583.68
  wait instruction        : yes
  microsecond timers      : yes
  tlb_entries             : 32
  extra interrupt vector  : yes
  hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
  isa                     : mips1 mips2 mips32r1 mips32r2
  ASEs implemented        : mips16 dsp mt
  shadow register sets    : 1
  kscratch registers      : 0
  core                    : 0
  VPE                     : 1
  VCED exceptions         : not available
  VCEI exceptions         : not available

  processor               : 2
  cpu model               : MIPS 1004Kc V2.15
  BogoMIPS                : 583.68
  wait instruction        : yes
  microsecond timers      : yes
  tlb_entries             : 32
  extra interrupt vector  : yes
  hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
  isa                     : mips1 mips2 mips32r1 mips32r2
  ASEs implemented        : mips16 dsp mt
  shadow register sets    : 1
  kscratch registers      : 0
  core                    : 1
  VPE                     : 0
  VCED exceptions         : not available
  VCEI exceptions         : not available

  processor               : 3
  cpu model               : MIPS 1004Kc V2.15
  BogoMIPS                : 583.68
  wait instruction        : yes
  microsecond timers      : yes
  tlb_entries             : 32
  extra interrupt vector  : yes
  hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
  isa                     : mips1 mips2 mips32r1 mips32r2
  ASEs implemented        : mips16 dsp mt
  shadow register sets    : 1
  kscratch registers      : 0
  core                    : 1
  VPE                     : 1
  VCED exceptions         : not available
  VCEI exceptions         : not available

  • cat /proc/meminfo

      root@WN-DX2033GR:~# cat /proc/meminfo
  MemTotal:         125196 kB
  MemFree:           60268 kB
  Buffers:            6308 kB
  Cached:            21208 kB
  SwapCached:            0 kB
  Active:            10544 kB
  Inactive:          19780 kB
  Active(anon):       3744 kB
  Inactive(anon):     2280 kB
  Active(file):       6800 kB
  Inactive(file):    17500 kB
  Unevictable:           0 kB
  Mlocked:               0 kB
  SwapTotal:             0 kB
  SwapFree:              0 kB
  Dirty:                 0 kB
  Writeback:             0 kB
  AnonPages:          2832 kB
  Mapped:             2856 kB
  Shmem:              3216 kB
  Slab:              16640 kB
  SReclaimable:       1988 kB
  SUnreclaim:        14652 kB
  KernelStack:         536 kB
  PageTables:          256 kB
  NFS_Unstable:          0 kB
  Bounce:                0 kB
  WritebackTmp:          0 kB
  CommitLimit:       62596 kB
  Committed_AS:       9404 kB
  VmallocTotal:    1048372 kB
  VmallocUsed:       15492 kB
  VmallocChunk:     978376 kB

  • cat /proc/mtd

      root@WN-DX2033GR:~# cat /proc/mtd
  dev:    size   erasesize  name
  mtd0: 07f80000 00020000 "ALL"
  mtd1: 00100000 00020000 "Bootloader"
  mtd2: 00100000 00020000 "Ubootenv"
  mtd3: 00100000 00020000 "Factory"
  mtd4: 03200000 00020000 "firmware"
  mtd5: 0307687e 00020000 "rootfs"
  mtd6: 00100000 00020000 "Config"
  mtd7: 03200000 00020000 "firmware_2"
  mtd8: 00100000 00020000 "Config_2"
  mtd9: 00100000 00020000 "persist"
  mtd10: 00100000 00020000 "idmkey"
  mtd11: 01380000 00020000 "Backup"
  mtd12: 00100000 00020000 "SecondBoot"

  • sys atsh

      root@WN-DX2033GR:~# sys atsh
  Firmware Version              : 3.10(XID.0)b19
  Boot Version                  : 1.24.06 | 12/09/2016 10:20:37
  Product Model                 : WN-DX2033GR
  First MAC Address             : 50:41:B9:xx:xx:90
  MAC Quantity                  : 4
  Serial Number                 : xxxxxxxxxxxx
  firmware Checksum             : bcc0562b
  Kernel Checksum               : a399b7b8
  RomFile Checksum              : 53078667
  Country Code                  : EA
  Boot Number                   : 1

  • switch --help

      root@WN-DX2033GR:~# switch --help
  Usage:
  switch acl etype add [ethtype] [portmap]              - drop etherytype packets
  switch acl dip add [dip] [portmap]                    - drop dip packets
  switch acl dip meter [dip] [portmap][meter:kbps]      - rate limit dip packets
  switch acl dip trtcm [dip] [portmap][CIR:kbps][CBS][PIR][PBS] - TrTCM dip packets
  switch acl port add [sport] [portmap]           - drop src port packets
  switch acl L4 add [2byes] [portmap]             - drop L4 packets with 2bytes payload
  switch add [mac] [portmap]                  - add an entry to switch table
  switch add [mac] [portmap] [vlan id]        - add an entry to switch table
  switch add [mac] [portmap] [vlan id] [age]  - add an entry to switch table
  switch clear                                - clear switch table
  switch del [mac]                            - delete an entry from switch table
  switch del [mac] [fid]                  - delete an entry from switch table
  switch dip add [dip] [portmap]                  - add a dip entry to switch table
  switch dip del [dip]                        - del a dip entry to switch table
  switch dip dump                                 - dump switch dip table
  switch dip clear                                - clear switch dip table
  switch dump            - dump switch table
  switch ingress-rate on [port] [Kbps]        - set ingress rate limit on port 0~4
  switch egress-rate on [port] [Kbps]         - set egress rate limit on port 0~4
  switch ingress-rate off [port]              - del ingress rate limit on port 0~4
  switch egress-rate off [port]               - del egress rate limit on port 0~4
  switch filt [mac]                           - add a SA filtering entry (with portmap 1111111) to switch table
  switch filt [mac] [portmap]                 - add a SA filtering entry to switch table
  switch filt [mac] [portmap] [vlan id]       - add a SA filtering entry to switch table
  switch filt [mac] [portmap] [vlan id] [age] - add a SA filtering entry to switch table
  switch igmpsnoop on [Query Interval] [default router portmap] - turn on IGMP snoop and  router port learning (Query Interval 1~255)
  switch igmpsnoop off                                  - turn off IGMP snoop and router port learning
  switch igmpsnoop enable [port#]                       - enable IGMP HW leave/join/Squery/Gquery
  switch igmpsnoop disable [port#]                      - disable IGMP HW leave/join/Squery/Gquery
  switch mymac [mac] [portmap]                  - add a mymac entry to switch table
  switch mirror monitor [portnumber]            - enable port mirror and indicate monitor port number
  switch mirror target [portnumber] [0:off, 1:rx, 2:tx, 3:all]  - set port mirror target
  switch phy [phy_addr]                   - dump phy register of specific port
  switch phy mt7530                       - dump mt7530 phy registers
  switch phy                                      - dump all phy registers
  switch pvid [port] [pvid]                - set pvid on port 0~4
  switch reg r [offset]                       - register read from offset
  switch reg w [offset] [value]               - register write value to offset
  switch reg d [offset]                       - register dump
  switch sip add [sip] [dip] [portmap]            - add a sip entry to switch table
  switch sip del [sip] [dip]                          - del a sip entry to switch table
  switch sip dump                                 - dump switch sip table
  switch sip clear                                - clear switch sip table
  switch tag on [port]                        - keep vlan tag for egress packet on prot 0~4
  switch tag off [port]                       - remove vlan tag for egress packet on port 0~4
  switch vlan dump                            - dump switch table
  switch vlan set [vlan idx (NULL)][vid] [portmap]  - set vlan id and associated member

  • switch vlan dump

      root@WN-DX2033GR:~# switch vlan dump
  vid  fid  portmap    s-tag
  1    0  -1111-11       0
  2    0  1----1--       0
  3    0  invalid
  4    0  invalid
  5    0  invalid
  6    0  invalid
  7    0  invalid
  8    0  invalid
  9    0  invalid
  10    0  invalid
  11    0  invalid
  12    0  invalid
  13    0  invalid
  14    0  invalid
  15    0  invalid
  16    0  invalid

  • swconfig list

      root@WN-DX2033GR:~# swconfig list
  Found: switch0 - mt7530

  • swconfig dev MT7530 show

      root@WN-DX2033GR:~# swconfig dev mt7530 show
  Global attributes:
  enable_vlan: 1
  enable_vlan4k: 1
  Port 0:
  mib: Port 0 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 0
  RxMulti    : 0
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 0
  Rx128Byte  : 0
  Rx256Byte  : 0
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 0
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 2
  link: port:0 link:down
  Port 1:
  mib: Port 1 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 0
  RxMulti    : 0
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 0
  Rx128Byte  : 0
  Rx256Byte  : 0
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 0
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 1
  link: port:1 link:down
  Port 2:
  mib: Port 2 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 0
  RxMulti    : 0
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 0
  Rx128Byte  : 0
  Rx256Byte  : 0
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 0
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 1
  link: port:2 link:down
  Port 3:
  mib: Port 3 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 0
  RxMulti    : 0
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 0
  Rx128Byte  : 0
  Rx256Byte  : 0
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 0
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 1
  link: port:3 link:down
  Port 4:
  mib: Port 4 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 1532
  TxMulti    : 203
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 708
  Tx65Byte   : 514
  Tx128Byte  : 18
  Tx256Byte  : 233
  Tx512Byte  : 60
  Tx1024Byte : 202
  TxByte     : 488627
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 1659
  RxMulti    : 582
  RxBroad    : 84
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 757
  Rx65Byte   : 1166
  Rx128Byte  : 149
  Rx256Byte  : 96
  Rx512Byte  : 157
  Rx1024Byte : 0
  RxByte     : 297785
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 1
  link: port:4 link:up speed:1000baseT full-duplex
  Port 5:
  mib: Port 5 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 99
  RxUni      : 0
  RxMulti    : 2
  RxBroad    : 97
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 1
  Rx128Byte  : 1
  Rx256Byte  : 97
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 33810
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 2
  link: port:5 link:up speed:1000baseT full-duplex
  Port 6:
  mib: Port 6 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 1659
  TxMulti    : 582
  TxBroad    : 84
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 757
  Tx65Byte   : 1166
  Tx128Byte  : 149
  Tx256Byte  : 96
  Tx512Byte  : 157
  Tx1024Byte : 0
  TxByte     : 297785
  RxDrop     : 0
  RxFiltered : 1
  RxUni      : 1532
  RxMulti    : 204
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 708
  Rx65Byte   : 514
  Rx128Byte  : 19
  Rx256Byte  : 233
  Rx512Byte  : 60
  Rx1024Byte : 202
  RxByte     : 488761
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 1
  link: port:6 link:up speed:1000baseT full-duplex
  Port 7:
  mib: Port 7 MIB counters
  TxDrop     : 0
  TxCRC      : 0
  TxUni      : 0
  TxMulti    : 0
  TxBroad    : 0
  TxCollision: 0
  TxSingleCol: 0
  TxMultiCol : 0
  TxDefer    : 0
  TxLateCol  : 0
  TxExcCol   : 0
  TxPause    : 0
  Tx64Byte   : 0
  Tx65Byte   : 0
  Tx128Byte  : 0
  Tx256Byte  : 0
  Tx512Byte  : 0
  Tx1024Byte : 0
  TxByte     : 0
  RxDrop     : 0
  RxFiltered : 0
  RxUni      : 0
  RxMulti    : 0
  RxBroad    : 0
  RxAlignErr : 0
  RxCRC      : 0
  RxUnderSize: 0
  RxFragment : 0
  RxOverSize : 0
  RxJabber   : 0
  RxPause    : 0
  Rx64Byte   : 0
  Rx65Byte   : 0
  Rx128Byte  : 0
  Rx256Byte  : 0
  Rx512Byte  : 0
  Rx1024Byte : 0
  RxByte     : 0
  RxCtrlDrop : 0
  RxIngDrop  : 0
  RxARLDrop  : 0

  pvid: 0
  link: port:7 link:down
  VLAN 1:
  ports: 1 2 3 4 6 7
  VLAN 2:
  ports: 0 5

  • bootlog

    
  ===================================================================
  MT7621   stage1 code 10:33:11 (ASIC)
  CPU=50000000 HZ BUS=16666666 HZ
  ==================================================================
  Change MPLL source from XTAL to CR...
  do MEMPLL setting..
  MEMPLL Config : 0x11100000
  3PLL mode + External loopback
  === XTAL-40Mhz === DDR-1200Mhz ===
  PLL2 FB_DL: 0xa, 1/0 = 564/460 29000000
  PLL3 FB_DL: 0x11, 1/0 = 513/511 45000000
  PLL4 FB_DL: 0x15, 1/0 = 609/415 55000000
  do DDR setting..[00320381]
  Apply DDR3 Setting...(use customer AC)
  0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
  --------------------------------------------------------------------------------
  0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1
  000E:|    0    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1
  000F:|    0    0    0    0    1    1    1    1    1    1    1    1    1    1    0    0
  0010:|    1    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0
  0011:|    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0
  0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
  rank 0 coarse = 15
  rank 0 fine = 72
  B:|    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0    0
  opt_dle value:8
  DRAMC_R0DELDLY[018]=00001E20
  ==================================================================
  RX      DQS perbit delay software calibration
  ==================================================================
  1.0-15 bit dq delay value
  ==================================================================
  bit|     0  1  2  3  4  5  6  7  8  9
  --------------------------------------
  0 |    9 9 9 11 7 9 8 7 7 8
  10 |    8 9 9 9 8 8
  --------------------------------------

  ==================================================================
  2.dqs window
  x=pass dqs delay value (min~max)center
  y=0-7bit DQ of every group
  input delay:DQS0 =32 DQS1 = 30
  ==================================================================
  bit     DQS0     bit      DQS1
  0  (1~62)31  8  (1~58)29
  1  (1~60)30  9  (1~58)29
  2  (0~58)29  10  (1~58)29
  3  (1~60)30  11  (1~57)29
  4  (0~60)30  12  (1~60)30
  5  (1~62)31  13  (1~58)29
  6  (1~60)30  14  (1~60)30
  7  (1~63)32  15  (1~60)30
  ==================================================================
  3.dq delay value last
  ==================================================================
  bit|    0  1  2  3  4  5  6  7  8   9
  --------------------------------------
  0 |    10 11 12 13 9 10 10 7 8 9
  10 |    9 10 9 10 8 8
  ==================================================================
  ==================================================================
  TX  perbyte calibration
  ==================================================================
  DQS loop = 15, cmp_err_1 = ffff0000
  dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
  dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
  DQ loop=15, cmp_err_1 = ffff0080
  dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=1
  DQ loop=14, cmp_err_1 = ffff0000
  dqs_perbyte_dly.last_dqdly_pass[0]=14,  finish count=2
  byte:0, (DQS,DQ)=(8,8)
  byte:1, (DQS,DQ)=(8,8)
  20,data:88
  [EMI] DRAMC calibration passed

  ===================================================================
  MT7621   stage1 code done
  CPU=50000000 HZ BUS=16666666 HZ
  ===================================================================

  U-Boot 1.1.3 (Dec  9 2016 - 10:20:35)

  Board: Ralink APSoC DRAM:  128 MB
  relocate_code Pointer at: 87fac000

  Config XHCI 40M PLL
  Allocate 16 byte aligned buffer: 87fdf010
  Enable NFI Clock
  # MTK NAND # : Use HW ECC
  NAND ID [C2 F1 80 95 02]
  Device found in MTK table, ID: c2f1, EXT_ID: 809502
  Support this Device in MTK table! c2f1
  select_chip
  [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
  Signature matched and data read!
  load_fact_bbt success 1023
  load fact bbt success
  [mtk_nand] probe successfully!
  mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8
  ....============================================
  Ralink UBoot Version: 5.0.0.0
  --------------------------------------------
  ASIC MT7621A DualCore (MAC to MT7530 Mode)
  DRAM_CONF_FROM: Auto-Detection
  DRAM_TYPE: DDR3
  DRAM bus: 16 bit
  Xtal Mode=3 OCP Ratio=1/3
  Flash component: NAND Flash
  Date:Dec  9 2016  Time:10:20:35
  ============================================
  icache: sets:256, ways:4, linesz:32 ,total:32768
  dcache: sets:256, ways:4, linesz:32 ,total:32768

  ##### The CPU freq = 880 MHZ ####
  estimate memory size =128 Mbytes
  #Reset_MT7530
  set LAN/WAN WLLLL
  .## Starting application at 0x81E00000 ...

  Z-LOADER V1.24 | 12/09/2016 10:20:37

  ..
  Checking image 1...
  Image Name:   3.10(XID.0)b19
  Image Type:   MIPS Linux Kernel Image (lzma compressed)
  Data Size:    1611586 Bytes =  1.5 MB
  Load Address: 80001000
  Entry Point:  80001000
  .........................   Verifying Combo Checksum ... ............................................................................................................................................................## Booting image at bc400000 ...
  Uncompressing Kernel Image ... OK
  No initrd
  ## Transferring control to Linux (at address 80001000) ...
  ## Giving linux memsize in MB, 128

  Starting kernel ...

  LINUX started...

  THIS IS ASIC

  SDK 5.0.S.0
  [    0.000000] Linux version 3.10.14 (*******@*******-PC-*******-******) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Thu Sep 3 17:22:37 CST 2020
  [    0.000000]
  [    0.000000]  The CPU feqenuce set to 880 MHz
  [    0.000000] GCMP present
  [    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
  [    0.000000] Software DMA cache coherency
  [    0.000000] Determined physical RAM map:
  [    0.000000]  memory: 08000000 @ 00000000 (usable)
  [    0.000000] Initrd not found or empty - disabling initrd
  [    0.000000] Zone ranges:
  [    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
  [    0.000000] Movable zone start for each node
  [    0.000000] Early memory node ranges
  [    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
  [    0.000000] Detected 3 available secondary CPU(s)
  [    0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  [    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  [    0.000000] PERCPU: Embedded 7 pages/cpu @81103000 s6464 r8192 d14016 u32768
  [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
  [    0.000000] Kernel command line: console=ttyS1,57600n8 BootImage=1 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
  [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  [    0.000000] Writing ErrCtl register=00004080
  [    0.000000] Readback ErrCtl register=00004080
  [    0.000000] Memory: 124944k/131072k available (3551k kernel code, 6128k reserved, 861k data, 252k init, 0k highmem)
  [    0.000000] Hierarchical RCU implementation.
  [    0.000000] NR_IRQS:128
  [    0.000000] console [ttyS1] enabled
  [    0.116000] Calibrating delay loop... 562.17 BogoMIPS (lpj=1124352)
  [    0.148000] pid_max: default: 32768 minimum: 301
  [    0.152000] Mount-cache hash table entries: 512
  [    0.156000] launch: starting cpu1
  [    0.160000] launch: cpu1 gone!
  [    0.160000] CPU1 revision is: 0001992f (MIPS 1004Kc)
  [    0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  [    0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  [    0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  [    0.192000] Synchronize counters for CPU 1: done.
  [    0.200000] launch: starting cpu2
  [    0.204000] launch: cpu2 gone!
  [    0.204000] CPU2 revision is: 0001992f (MIPS 1004Kc)
  [    0.204000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  [    0.204000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  [    0.204000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  [    0.232000] Synchronize counters for CPU 2: done.
  [    0.240000] launch: starting cpu3
  [    0.244000] launch: cpu3 gone!
  [    0.244000] CPU3 revision is: 0001992f (MIPS 1004Kc)
  [    0.244000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  [    0.244000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  [    0.244000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  [    0.272000] Synchronize counters for CPU 3: done.
  [    0.280000] Brought up 4 CPUs
  [    0.284000] NET: Registered protocol family 16
  [    0.576000] release PCIe RST: RALINK_RSTCTRL = 7000000
  [    0.580000] PCIE PHY initialize
  [    0.584000] ***** Xtal 40MHz *****
  [    0.588000] start MT7621 PCIe register access
  [    1.164000] RALINK_RSTCTRL = 7000000
  [    1.168000] RALINK_CLKCFG1 = 77ffeff8
  [    1.172000]
  [    1.172000] *************** MT7621 PCIe RC mode *************
  [    1.652000] PCIE2 no card, disable it(RST&CLK)
  [    1.656000] pcie_link status = 0x3
  [    1.660000] RALINK_RSTCTRL= 3000000
  [    1.664000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
  [    1.668000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
  [    1.672000] PCIE0 enabled
  [    1.676000] PCIE1 enabled
  [    1.680000] interrupt enable status: 300000
  [    1.684000] Port 1 N_FTS = 1b105000
  [    1.688000] Port 0 N_FTS = 1b105000
  [    1.692000] config reg done
  [    1.696000] init_rt2880pci done
  [    1.716000] bio: create slab  at 0
  [    1.720000] SCSI subsystem initialized
  [    1.724000] usbcore: registered new interface driver usbfs
  [    1.728000] usbcore: registered new interface driver hub
  [    1.732000] usbcore: registered new device driver usb
  [    1.736000] PCI host bridge to bus 0000:00
  [    1.740000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
  [    1.744000] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
  [    1.748000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  [    1.752000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  [    1.756000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  [    1.760000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
  [    1.764000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
  [    1.768000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
  [    1.772000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
  [    1.776000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
  [    1.780000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
  [    1.784000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
  [    1.788000] pci 0000:00:00.0: PCI bridge to [bus 01]
  [    1.792000] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
  [    1.796000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
  [    1.800000] pci 0000:00:01.0: PCI bridge to [bus 02]
  [    1.804000] pci 0000:00:01.0:   bridge window [mem 0x60100000-0x601fffff]
  [    1.808000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
  [    1.812000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
  [    1.816000] BAR0 at slot 0 = 0
  [    1.820000] bus=0x0, slot = 0x0
  [    1.824000] res[0]->start = 0
  [    1.828000] res[0]->end = 0
  [    1.832000] res[1]->start = 60200000
  [    1.836000] res[1]->end = 6020ffff
  [    1.840000] res[2]->start = 0
  [    1.844000] res[2]->end = 0
  [    1.848000] res[3]->start = 0
  [    1.852000] res[3]->end = 0
  [    1.856000] res[4]->start = 0
  [    1.860000] res[4]->end = 0
  [    1.864000] res[5]->start = 0
  [    1.868000] res[5]->end = 0
  [    1.872000] BAR0 at slot 1 = 0
  [    1.876000] bus=0x0, slot = 0x1
  [    1.880000] res[0]->start = 0
  [    1.884000] res[0]->end = 0
  [    1.888000] res[1]->start = 60210000
  [    1.892000] res[1]->end = 6021ffff
  [    1.896000] res[2]->start = 0
  [    1.900000] res[2]->end = 0
  [    1.904000] res[3]->start = 0
  [    1.908000] res[3]->end = 0
  [    1.912000] res[4]->start = 0
  [    1.916000] res[4]->end = 0
  [    1.920000] res[5]->start = 0
  [    1.924000] res[5]->end = 0
  [    1.928000] bus=0x1, slot = 0x0, irq=0x4
  [    1.932000] res[0]->start = 60000000
  [    1.936000] res[0]->end = 600fffff
  [    1.940000] res[1]->start = 0
  [    1.944000] res[1]->end = 0
  [    1.948000] res[2]->start = 0
  [    1.952000] res[2]->end = 0
  [    1.956000] res[3]->start = 0
  [    1.960000] res[3]->end = 0
  [    1.964000] res[4]->start = 0
  [    1.968000] res[4]->end = 0
  [    1.972000] res[5]->start = 0
  [    1.976000] res[5]->end = 0
  [    1.980000] bus=0x2, slot = 0x1, irq=0x18
  [    1.984000] res[0]->start = 60100000
  [    1.988000] res[0]->end = 601fffff
  [    1.992000] res[1]->start = 0
  [    1.996000] res[1]->end = 0
  [    2.000000] res[2]->start = 0
  [    2.004000] res[2]->end = 0
  [    2.008000] res[3]->start = 0
  [    2.012000] res[3]->end = 0
  [    2.016000] res[4]->start = 0
  [    2.020000] res[4]->end = 0
  [    2.024000] res[5]->start = 0
  [    2.028000] res[5]->end = 0
  [    2.032000] Switching to clocksource MIPS
  [    2.036000] NET: Registered protocol family 2
  [    2.044000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  [    2.060000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
  [    2.072000] TCP: Hash tables configured (established 1024 bind 1024)
  [    2.084000] TCP: reno registered
  [    2.092000] UDP hash table entries: 256 (order: 1, 8192 bytes)
  [    2.104000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  [    2.116000] NET: Registered protocol family 1
  [    2.212000] 4 CPUs re-calibrate udelay(lpj = 1167360)
  [    2.224000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  [    2.236000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  [    2.260000] io scheduler noop registered (default)
  [    2.268000] reg_int_mask=0, INT_MASK= 0
  [    2.276000] HSDMA_init
  [    2.280000]
  [    2.280000]  hsdma_phy_tx_ring0 = 0x0fd18000, hsdma_tx_ring0 = 0xafd18000
  [    2.300000]
  [    2.300000]  hsdma_phy_rx_ring0 = 0x0fcf4000, hsdma_rx_ring0 = 0xafcf4000
  [    2.316000] TX_CTX_IDX0 = 0
  [    2.320000] TX_DTX_IDX0 = 0
  [    2.324000] RX_CRX_IDX0 = 3ff
  [    2.332000] RX_DRX_IDX0 = 0
  [    2.336000] set_fe_HSDMA_glo_cfg
  [    2.344000] HSDMA_GLO_CFG = 465
  [    2.356000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  [    2.368000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
  [    2.380000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
  [    2.396000] Ralink gpio driver initialized
  [    2.404000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
  [    2.416000] Allocate 16 byte aligned buffer: 804a1c20
  [    2.428000] Enable NFI Clock
  [    2.432000] # MTK NAND # : Use HW ECC
  [    2.440000] NAND ID [C2 F1 80 95 02, 00809502]
  [    2.448000] Device found in MTK table, ID: c2f1, EXT_ID: 809502
  [    2.460000] Support this Device in MTK table! c2f1
  [    2.472000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  [    2.496000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
  [    2.508000] Scanning device for bad blocks
  [    2.756000] Signature matched and data read!
  [    2.764000] load_fact_bbt success 1023
  [    2.772000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.792000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.808000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.828000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.848000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.868000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.888000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.908000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  [    2.928000] Creating 12 MTD partitions on "MT7621-NAND":
  [    2.940000] 0x000000000000-0x000007f80000 : "ALL"
  [    2.948000] 0x000000000000-0x000000100000 : "Bootloader"
  [    2.960000] 0x000000100000-0x000000200000 : "Ubootenv"
  [    2.972000] 0x000000200000-0x000000300000 : "Factory"
  [    2.984000] 0x000000400000-0x000003600000 : "firmware"
  [    2.996000] 0x000000589782-0x000003600000 : "rootfs"
  [    3.008000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  [    3.040000] 0x000003600000-0x000003700000 : "Config"
  [    3.052000] 0x000003700000-0x000006900000 : "firmware_2"
  [    3.064000] 0x000006900000-0x000006a00000 : "Config_2"
  [    3.072000] 0x000006a00000-0x000006b00000 : "persist"
  [    3.084000] 0x000006b00000-0x000006c00000 : "idmkey"
  [    3.096000] 0x000006c00000-0x000007f80000 : "Backup"
  [    3.108000] 0x000000300000-0x000000400000 : "SecondBoot"
  [    3.120000] [mtk_nand] probe successfully!
  [    3.128000] rootfs = 589782 to dc0000
  [    3.132000] PPP generic driver version 2.4.2
  [    3.144000] NET: Registered protocol family 24
  [    3.152000] PPTP driver version 0.8.5
  [    3.160000] rdm_major = 253
  [    3.164000] netif_napi_add() called with weight 128 on device eth0
  [    3.176000] GMAC1_MAC_ADRH -- : 0x00005041
  [    3.184000] GMAC1_MAC_ADRL -- : 0xb9209990
  [    3.196000] Ralink APSoC Ethernet Driver Initilization. v3.1  1024 rx/tx descriptors allocated, mtu = 1500!
  [    3.212000] NAPI enable, Tx Ring = 1088, Rx Ring = 1024
  [    3.224000] GMAC1_MAC_ADRH -- : 0x00005041
  [    3.232000] GMAC1_MAC_ADRL -- : 0xb9209990
  [    3.240000] register mt7530
  [    3.248000] PROC INIT OK!
  [    3.252000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  [    3.264000] ehci-pci: EHCI PCI platform driver
  [    3.272000] *****run project phy.
  [    3.288000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.304000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.324000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.344000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.364000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.384000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.400000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.420000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.436000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.452000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.484000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.500000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.516000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.532000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.548000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.564000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.580000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.596000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.612000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.628000] FM_OUT value: u4FmOut = 0(0x00000000)
  [    3.756000] xhci-hcd xhci-hcd: xHCI Host Controller
  [    3.764000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
  [    3.780000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
  [    3.792000] hub 1-0:1.0: USB hub found
  [    3.800000] hub 1-0:1.0: 2 ports detected
  [    3.808000] xhci-hcd xhci-hcd: xHCI Host Controller
  [    3.816000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
  [    3.832000] hub 2-0:1.0: USB hub found
  [    3.840000] hub 2-0:1.0: 1 port detected
  [    3.848000] usbcore: registered new interface driver usb-storage
  [    3.860000] gre: GRE over IPv4 demultiplexor driver
  [    3.868000] TCP: cubic registered
  [    3.876000] NET: Registered protocol family 10
  [    3.884000] NET: Registered protocol family 17
  [    3.896000] Bridge firewalling registered
  [    3.904000] 8021q: 802.1Q VLAN Support v1.8
  [    3.912000] console [netcon0] enabled
  [    3.920000] netconsole: network logging started
  [    3.936000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
  [    3.948000] Freeing unused kernel memory: 252K (80451000 - 80490000)
  procd: Console is alive
  procd: - preinit -
  [    5.368000] 50:41:FFFFFFB9:xx:FFFFFFxx:FFFFFF90
  [    5.376000] Raeth v3.1 (NAPI
  [    5.384000] )
  [    5.388000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
  [    5.404000] phy_free_head is 0xf6f6000!!!
  [    5.412000] phy_free_tail_phy is 0xf6f7ff0!!!
  [    5.420000] txd_pool=af738000 phy_txd_pool=0F738000
  [    5.428000] ei_local->skb_free start address is 0x87eea6e0.
  [    5.440000] free_txd: 0f738010, ei_local->cpu_ptr: 0F738000
  [    5.452000]  POOL  HEAD_PTR | DMA_PTR | CPU_PTR
  [    5.460000] ----------------+---------+--------
  [    5.468000]      0xaf738000 0x0F738000 0x0F738000
  [    5.480000]
  [    5.480000] phy_qrx_ring = 0x0f6f5000, qrx_ring = 0xaf6f5000
  [    5.496000]
  [    5.496000] phy_rx_ring0 = 0x0f748000, rx_ring[0] = 0xaf748000
  [    5.532000] MT7530 Reset Completed!!
  [    5.544000] change HW-TRAP to 0x117c8f
  [    5.552000] set LAN/WAN WLLLL
  [    5.564000] GMAC1_MAC_ADRH -- : 0x00005041
  [    5.572000] GMAC1_MAC_ADRL -- : 0xb9209990
  [    5.580000] GDMA2_MAC_ADRH -- : 0x00005041
  [    5.588000] GDMA2_MAC_ADRL -- : 0xb9209992
  [    5.596000] eth1: ===> VirtualIF_open
  [    5.604000] MT7621 GE2 link rate to 1G
  [    5.604000] CDMA_CSG_CFG = 81000000
  [    5.604000] GDMA1_FWD_CFG = 20710000
  [    5.604000] GDMA2_FWD_CFG = 20710000
  [    5.728000] led=9, on=1, off=1, blinks,=1, reset=1, time=4000 low_trigger=1
  Press the [f] key and hit [enter] to enter failsafe mode
  Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  [    8.832000] led=9, on=1, off=1, blinks,=1, reset=1, time=4000 low_trigger=1
  Could not open mtd device: /dev/mtd5
  reading ro[    8.944000] ra2880stop()...otfs failed
  mouDone
  [    8.952000] eth1: ===> VirtualIF_close

  [    8.964000] Free TX/RX Ring Memory!
  procd: - early -
  procd: - ubus -
  procd: - init -
  Please press Enter to activate this console.
  [   11.040000] jffs2: notice: (774) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  [   11.168000] jffs2: notice: (777) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  ##### Backup Config. #####
  [   12.584000] Initializing XFRM netlink socket
  [   12.592000] NET: Registered protocol family 15
  [   12.604000] sbdev driver(major: 254) installed.
  [   12.612000] wpdev driver(major: 250) installed.
  [   12.636000] l2tp_core: L2TP core driver, V2.0
  [   12.648000] l2tp_netlink: L2TP netlink interface
  [   12.656000] ip_gre: GRE over IPv4 tunneling driver
  [   12.676000] ip_tables: (C) 2000-2006 Netfilter Core Team
  [   12.688000] Type=Restricted Cone
  [   12.696000] nf_conntrack version 0.5.0 (1956 buckets, 7824 max)
  [   12.712000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  [   12.744000] ebt_time: kernel timezone is -0000
  [   12.756000] Ebtables v2.0 registered
  [   12.768000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  [   12.848000] Netfilter messages via NETLINK v0.30.
  [   12.860000] PPP MPPE Compression module registered
  [   12.872000] Ralink APSoC Hardware Watchdog Timer
  [   12.904000] xt_time: kernel timezone is -0000
  [   12.920000] ctnetlink v0.93: registering with nfnetlink.
  [   15.804000] mtd: ALL locked
  [   15.812000] mtd: Bootloader locked
  [   15.816000] mtd: Ubootenv locked
  [   15.824000] mtd: Factory locked
  [   15.832000] mtd_locked init
  [   17.436000] 50:41:FFFFFFB9:xx:FFFFFFxx:FFFFFF90
  [   17.444000] Raeth v3.1 (NAPI
  [   17.452000] )
  [   17.456000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
  [   17.472000] phy_free_head is 0xedcc000!!!
  [   17.480000] phy_free_tail_phy is 0xedcdff0!!!
  [   17.488000] txd_pool=aefb0000 phy_txd_pool=0EFB0000
  [   17.500000] ei_local->skb_free start address is 0x87eea6e0.
  [   17.512000] free_txd: 0efb0010, ei_local->cpu_ptr: 0EFB0000
  [   17.520000]  POOL  HEAD_PTR | DMA_PTR | CPU_PTR
  [   17.532000] ----------------+---------+--------
  [   17.540000]      0xaefb0000 0x0EFB0000 0x0EFB0000
  [   17.548000]
  [   17.548000] phy_qrx_ring = 0x0efdf000, qrx_ring = 0xaefdf000
  [   17.568000]
  [   17.568000] phy_rx_ring0 = 0x0efe8000, rx_ring[0] = 0xaefe8000
  [   17.608000] MT7530 Reset Completed!!
  [   17.624000] change HW-TRAP to 0x117c8f
  [   17.632000] set LAN/WAN WLLLL
  [   17.644000] GMAC1_MAC_ADRH -- : 0x00005041
  [   17.652000] GMAC1_MAC_ADRL -- : 0xb9209990
  [   17.660000] eth1: ===> VirtualIF_open
  [   17.668000] MT7621 GE2 link rate to 1G
  [   17.668000] CDMA_CSG_CFG = 81000000
  [   17.668000] GDMA1_FWD_CFG = 20710000
  [   17.668000] GDMA2_FWD_CFG = 20710000
  [   17.668000] device eth0 entered promiscuous mode
  [   17.668000] br-lan: port 1(eth0) entered forwarding state
  [   17.668000] br-lan: port 1(eth0) entered forwarding state
  [   17.668000] eth1: ===> VirtualIF_open
  [   19.672000] br-lan: port 1(eth0) entered forwarding state
  [   22.216000] register rlt_drv
  [   22.224000]
  [   22.224000]
  [   22.224000] === pAd = c1581000, size = 1244888 ===
  [   22.224000]
  [   22.244000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
  [   22.256000] <-- RTMPAllocAdapterBlock, Status=0
  [   22.268000] pAd->CSRBaseAddress =0xc1480000, csr_addr=0xc1480000!
  [   22.280000] device_id =0x7603
  [   22.284000] RtmpChipOpsHook(507): Not support for HIF_MT yet!
  [   22.296000] mt7603_init()-->
  [   22.300000] mt_bcn_buf_init(224): Not support for HIF_MT yet!
  [   22.312000] <--mt7603_init()
  [   22.328000] TX_BCN DESC aefd4000 size = 320
  [   22.336000] RX[0] DESC aecf6000 size = 2048
  [   22.348000] RX[1] DESC aecf7000 size = 2048
  [   22.360000] RT_CfgSetMacAddress : invalid length (0)
  [   22.372000] E2pAccessMode=2
  [   22.380000] cfg_mode=9
  [   22.384000] cfg_mode=9
  [   22.388000] wmode_band_equal(): Band Equal!
  [   22.400000] APSDCapable[0]=1
  [   22.404000] APSDCapable[1]=1
  [   22.412000] APSDCapable[2]=1
  [   22.416000] APSDCapable[3]=1
  [   22.420000] APSDCapable[4]=1
  [   22.428000] APSDCapable[5]=1
  [   22.432000] APSDCapable[6]=1
  [   22.440000] APSDCapable[7]=1
  [   22.444000] APSDCapable[8]=1
  [   22.452000] APSDCapable[9]=1
  [   22.456000] APSDCapable[10]=1
  [   22.464000] APSDCapable[11]=1
  [   22.468000] APSDCapable[12]=1
  [   22.476000] APSDCapable[13]=1
  [   22.480000] APSDCapable[14]=1
  [   22.488000] APSDCapable[15]=1
  [   22.492000] default ApCliAPSDCapable[0]=1
  [   22.976000] Key1Str is Invalid key length(0) or Type(0)
  [   22.984000] Key1Str is Invalid key length(0) or Type(0)
  [   22.996000] Key1Str is Invalid key length(0) or Type(0)
  [   23.004000] Key1Str is Invalid key length(0) or Type(0)
  [   23.016000] Key2Str is Invalid key length(0) or Type(0)
  [   23.028000] Key2Str is Invalid key length(0) or Type(0)
  [   23.036000] Key2Str is Invalid key length(0) or Type(0)
  [   23.048000] Key2Str is Invalid key length(0) or Type(0)
  [   23.060000] Key3Str is Invalid key length(0) or Type(0)
  [   23.068000] Key3Str is Invalid key length(0) or Type(0)
  [   23.080000] Key3Str is Invalid key length(0) or Type(0)
  [   23.092000] Key3Str is Invalid key length(0) or Type(0)
  [   23.100000] Key4Str is Invalid key length(0) or Type(0)
  [   23.112000] Key4Str is Invalid key length(0) or Type(0)
  [   23.124000] Key4Str is Invalid key length(0) or Type(0)
  [   23.132000] Key4Str is Invalid key length(0) or Type(0)
  [   23.176000] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
  [   23.188000] [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0
  [   23.200000] [PMF]Set_PMFMFPC_Proc:: apidx=2, Desired MFPC=0
  [   23.208000] [PMF]Set_PMFMFPC_Proc:: apidx=3, Desired MFPC=0
  [   23.220000] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
  [   23.232000] [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0
  [   23.244000] [PMF]Set_PMFMFPR_Proc:: apidx=2, Desired MFPR=0
  [   23.256000] [PMF]Set_PMFMFPR_Proc:: apidx=3, Desired MFPR=0
  [   23.264000] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
  [   23.276000] [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0
  [   23.292000] [PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0
  [   23.304000] [PMF]Set_PMFSHA256_Proc:: apidx=3, Desired PMFSHA256=0
  [   23.316000] FW Version:tssi_1222
  [   23.324000] FW Build Date:20151222134859
  [   23.332000] CmdAddressLenReq:(ret = 0)
  [   23.340000] CmdFwStartReq: override = 1, address = 1048576
  [   23.352000] CmdStartDLRsp: WiFI FW Download Success
  [   23.368000] AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
  [   23.380000] efuse_probe: efuse = 10000002
  [   23.388000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
  [   23.400000] RtmpEepromGetDefault::e2p_dafault=1
  [   23.408000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
  [   23.424000] NVM is FLASH mode, flash_offset = 0x40000
  [   23.436000] 1. Phy Mode = 14
  [   23.440000] @@@  NICReadEEPROMParameters : pAd->FWLoad=0
  [   23.600000] Country Region from e2p = ffff
  [   23.608000] tssi_1_target_pwr_g_band = 32
  [   23.616000] 2. Phy Mode = 14
  [   23.624000] 3. Phy Mode = 14
  [   23.628000] NICInitPwrPinCfg(14): Not support for HIF_MT yet!
  [   23.640000] NICInitializeAsic(584): Not support rtmp_mac_sys_reset () for HIF_MT yet!
  [   23.656000] mt_mac_init()-->
  [   23.664000] mt7603_init_mac_cr()-->
  [   23.672000] AsicSetMacMaxLen(1814): Set the Max RxPktLen=1024!
  [   23.684000] <--mt_mac_init()
  start daemon
  [   23.688000]  WTBL Segment 1 info:
  [   23.696000]          MemBaseAddr/FID:0x28000/0
  [   23.704000]          EntrySize/Cnt:32/128
  [   23.712000]  WTBL Segment 2 info:
  [   23.720000]          MemBaseAddr/FID:0x40000/0
  [   23.728000]          EntrySize/Cnt:64/128
  [   23.732000]  WTBL Segment 3 info:
  [   23.740000]          MemBaseAddr/FID:0x42000/64
  [   23.748000]          EntrySize/Cnt:64/128
  [   23.756000]  WTBL Segment 4 info:
  [   23.760000]          MemBaseAddr/FID:0x44000/128
  [   23.768000]          EntrySize/Cnt:32/128
  [   23.776000] MtAsicACQueue: Write CR:21510, Value=10421
  [   23.784000] MtAsicACQueue: Write CR:21500, Value=10421
  [   23.796000] AntCfgInit(2558): Not support for HIF_MT yet!
  [   23.808000] RTMPSetPhyMode(): channel out of range, use first ch=0
  [   23.820000] MCS Set = ff ff 00 00 01
  [   24.144000] led=8, on=0, off=4000, blinks,=0, reset=0, time=1 low_trigger=1
  [   24.220000] led=8, on=0, off=4000, blinks,=0, reset=0, time=1 low_trigger=0
  [   24.292000] led=8, on=0, off=4000, blinks,=0, reset=0, time=1 low_trigger=1
  [   27.456000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
  [   27.468000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  [   27.480000] [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
  [   27.492000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  [   27.504000] [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
  [   27.516000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  [   27.528000] [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
  [   27.540000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  [   27.552000] AsicSetRalinkBurstMode(4127): Not support for HIF_MT yet!
  [   27.564000] RTMPSetPiggyBack(876): Not support for HIF_MT yet!
  [   27.596000] AsicSetTxPreamble(4114): Not support for HIF_MT yet!
  [   27.608000] AsicAddSharedKeyEntry(1980): Not support for HIF_MT yet!
  [   27.624000] AsicAddSharedKeyEntry(1980): Not support for HIF_MT yet!
  [   27.640000] AsicAddSharedKeyEntry(1980): Not support for HIF_MT yet!
  [   27.652000] AsicAddSharedKeyEntry(1980): Not support for HIF_MT yet!
  [   27.668000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
  [   27.676000] Main bssid = 50:41:b9:xx:xx:90
  [   27.688000] <==== rt28xx_init, Status=0
  [   27.700000] first MBSSID is 50 41 b9 xx xx 90
  [   27.708000] first MBSSID is 50 41 b9 xx xx 90
  [   27.720000] first MBSSID is 50 41 b9 xx xx 90
  [   27.728000] first MBSSID is 50 41 b9 xx xx 90
  [   27.736000] first MBSSID is 50 41 b9 xx xx 90
  [   27.744000] @@@ ed_monitor_exit : ===>
  [   27.752000] @@@ ed_monitor_exit : <===
  [   27.760000] mt7603_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f
  [   27.772000] mt7603_set_ed_cca: pAd->CommonCfg.CountryCode = JP
  [   27.784000] mt7603_set_ed_cca: TURN OFF NBID mac 0x10610 = 0x36a1282a
  [   27.796000] WiFi Startup Cost (ra0): 5.468s
  [   28.284000] device ra0 entered promiscuous mode
  [   28.292000] br-lan: port 2(ra0) entered forwarding state
  [   28.304000] br-lan: port 2(ra0) entered forwarding state
  [   30.308000] br-lan: port 2(ra0) entered forwarding state
  [   31.568000] register mt_drv
  [   31.584000]
  [   31.584000]
  [   31.584000] === pAd = c3a81000, size = 3623712 ===
  [   31.584000]
  [   31.604000] <-- RTMPAllocAdapterBlock, Status=0
  [   31.616000] pAd->PciHif.CSRBaseAddress =0xc3980000, csr_addr=0xc3980000!
  [   31.628000] RTMPInitPCIeDevice():device_id=0x7615
  [   31.636000] DriverOwn()::Try to Clear FW Own...
  [   31.956000] DriverOwn()::Success to clear FW Own
  [   31.968000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
  [   31.980000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
  [   31.992000] RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0
  [   32.004000] mt7615_init()-->
  [   32.012000] Use 1st ePAeLNA default bin.
  [   32.020000] <--mt7615_init()
  [   32.024000] ChipOpsMCUHook
  [   32.036000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
  [   32.052000] cut_through_token_list_init(): 84eaed08,84eaed08
  [   32.064000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
  [   32.080000] cut_through_token_list_init(): 84eaed18,84eaed18
  [   32.092000] <-- RTMPAllocTxRxRingMemory, Status=0
  [   32.116000] DriverOwn()::Return since already in Driver Own...
  [   32.132000] RT_CfgSetMacAddress : invalid length (0)
  [   32.144000] RT_CfgSetMacAddress : invalid length (0)
  [   32.152000] RT_CfgSetMacAddress : invalid length (0)
  [   32.164000] RT_CfgSetMacAddress : invalid length (0)
  [   32.172000] E2pAccessMode=2
  [   32.180000] SSID[0]=IODATA-209990-5G, EdcaIdx=0
  [   32.188000] SSID[1]=IO-Guest-209990-5G, EdcaIdx=0
  [   32.200000] RTMPSetProfileParameters(): DBDC Mode=0
  [   32.208000] cfg_mode=14
  [   32.216000] cfg_mode=14
  [   32.220000] wmode_band_equal(): Band Equal!
  [   32.228000] APEdca0
  [   32.232000] APEdca1
  [   32.236000] APEdca2
  [   32.244000] APEdca3
  [   32.248000] APSDCapable[0]=1
  [   32.252000] APSDCapable[1]=1
  [   32.260000] APSDCapable[2]=1
  [   32.264000] APSDCapable[3]=1
  [   32.272000] APSDCapable[4]=1
  [   32.276000] APSDCapable[5]=1
  [   32.284000] APSDCapable[6]=1
  [   32.288000] APSDCapable[7]=1
  [   32.296000] APSDCapable[8]=1
  [   32.300000] APSDCapable[9]=1
  [   32.308000] APSDCapable[10]=1
  [   32.312000] APSDCapable[11]=1
  [   32.320000] APSDCapable[12]=1
  [   32.324000] APSDCapable[13]=1
  [   32.332000] APSDCapable[14]=1
  [   32.336000] APSDCapable[15]=1
  [   32.340000] default ApCliAPSDCapable[0]=1
  [   32.348000] default ApCliAPSDCapable[1]=1
  [   32.360000] DfsZeroWait Support=0/0
  [   32.384000] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
  [   32.396000] [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0
  [   32.404000] [PMF]Set_PMFMFPC_Proc:: apidx=2, Desired MFPC=0
  [   32.416000] [PMF]Set_PMFMFPC_Proc:: apidx=3, Desired MFPC=0
  [   32.428000] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
  [   32.440000] [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0
  [   32.452000] [PMF]Set_PMFMFPR_Proc:: apidx=2, Desired MFPR=0
  [   32.460000] [PMF]Set_PMFMFPR_Proc:: apidx=3, Desired MFPR=0
  [   32.472000] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
  [   32.484000] [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0
  [   32.496000] [PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0
  [   32.512000] [PMF]Set_PMFSHA256_Proc:: apidx=3, Desired PMFSHA256=0
  [   32.532000] HT: Ext Channel = BELOW
  [   32.564000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
  [   32.584000] Top Init Done!
  [   32.592000] Use alloc_skb
  [   32.596000] RX[0] DESC acdb4000 size = 8192
  [   32.608000] RX[1] DESC acdb6000 size = 8192
  [   32.616000] Hif Init Done!
  [   32.624000] ctl->txq = c3df1a60
  [   32.628000] ctl->rxq = c3df1a6c
  [   32.636000] ctl->ackq = c3df1a78
  [   32.640000] ctl->kickq = c3df1a84
  [   32.648000] ctl->tx_doneq = c3df1a90
  [   32.656000] ctl->rx_doneq = c3df1a9c
  [   32.664000] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
  [   32.676000] mt7615_fw_prepare(2629): MT7615_E3, USE E3 patch and ram code binary image
  [   32.692000] AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(10206)
  [   32.704000] AndesRestartCheck: Current TOP_MISC2(0x1)
  [   32.716000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
  [   32.728000] 20161013140927a
  [   32.736000]
  [   32.740000] platform =
  [   32.744000] ALPS
  [   32.748000] hw/sw version =
  [   32.752000] 8a108a10
  [   32.756000] patch version =
  [   32.764000] 00000010
  [   32.768000] Patch SEM Status=2
  [   32.772000] MtCmdPatchSemGet:(ret = 0)
  [   32.780000]
  [   32.780000] Patch is not ready && get semaphore success, SemStatus(2)
  [   32.796000] EventGenericEventHandler: CMD Success
  [   32.808000] MtCmdAddressLenReq:(ret = 0)
  [   32.816000] MtCmdPatchFinishReq
  [   32.832000] EventGenericEventHandler: CMD Success
  [   32.840000] Send checksum req..
  [   32.848000] Patch SEM Status=3
  [   32.856000] MtCmdPatchSemGet:(ret = 0)
  [   32.860000]
  [   32.860000] Release patch semaphore, SemStatus(3)
  [   32.876000] AndesMTEraseRomPatch
  [   32.880000] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
  [   32.892000] AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(456424)
  [   32.904000] Build Date:_201610141152
  [   32.912000] Build Date:_201610141152
  [   32.920000] AndesRestartCheck: Current TOP_MISC2(0x1)
  [   32.928000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
  [   32.944000] EventGenericEventHandler: CMD Success
  [   32.952000] MtCmdAddressLenReq:(ret = 0)
  [   32.968000] EventGenericEventHandler: CMD Success
  [   32.976000] MtCmdAddressLenReq:(ret = 0)
  [   32.984000] MtCmdFwStartReq: override = 1, address = 540672
  [   32.996000] EventGenericEventHandler: CMD Success
  [   33.004000] Build Date:_201609191315
  [   33.012000] EventGenericEventHandler: CMD Success
  [   33.020000] MtCmdAddressLenReq:(ret = 0)
  [   33.032000] MtCmdFwStartReq: override = 4, address = 0
  [   33.108000] EventGenericEventHandler: CMD Success
  [   33.148000] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
  [   33.156000] MCU Init Done!
  [   33.164000] efuse_probe: efuse = 10000212
  [   33.172000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
  [   33.180000] RtmpEepromGetDefault::e2p_dafault=1
  [   33.192000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
  [   33.208000] NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000]
  [   33.228000] NICReadEEPROMParameters: EEPROM 0x52 b307
  [   33.244000] MtCmdSetTxLpfCal:(ret = 0)
  [   33.252000] MtCmdSetTxIqCal:(ret = 0)
  [   33.260000] MtCmdSetTxDcCal:(ret = 0)
  [   33.264000] MtCmdSetRxFiCal:(ret = 0)
  [   33.272000] MtCmdSetRxFdCal:(ret = 0)
  [   33.280000] MtCmdSetRxFdCal:(ret = 0)
  [   33.288000] MtCmdSetRxFdCal:(ret = 0)
  [   33.296000] MtCmdSetRxFdCal:(ret = 0)
  [   33.304000] MtCmdSetRxFdCal:(ret = 0)
  [   33.308000] MtCmdSetRxFdCal:(ret = 0)
  [   33.316000] MtCmdSetRxFdCal:(ret = 0)
  [   33.324000] MtCmdSetRxFdCal:(ret = 0)
  [   33.332000] MtCmdSetRxFdCal:(ret = 0)
  [   33.340000] NICReadEEPROMParameters: EEPROM 0x52 b307
  [   33.904000] Country Region from e2p = 101
  [   33.912000] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
  [   33.924000] rtmp_read_txpwr_from_eeprom(233): Don't Support this now!
  [   33.936000] RTMPReadTxPwrPerRate(1381): Don't Support this now!
  [   33.948000] RcRadioInit(): DbdcMode=0, ConcurrentBand=1
  [   33.960000] RcRadioInit(): pRadioCtrl=84eaf440,Band=0,rfcap=3,channel=1,PhyMode=2
  [   33.972000] MtCmdSetDbdcCtrl:(ret = 0)
  [   33.980000] Band Rf: 1, Phy Mode: 2
  [   33.988000] AntCfgInit(2637): Not support for HIF_MT yet!
  [   34.000000] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
  [   34.012000] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
  [   34.024000] EEPROM Init Done!
  [   34.028000] mt_mac_init()-->
  [   34.036000] mt_mac_pse_init(2715): Don't Support this now!
  [   34.044000] mt7615_init_mac_cr()-->
  [   34.052000] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
  [   34.064000] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
  [   34.072000] MtAsicSetMacMaxLen(1288): Not finish Yet!
  [   34.084000] <--mt_mac_init()
  [   34.092000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
  [   34.108000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
  [   34.120000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
  [   34.132000] MAC Init Done!
  [   34.136000] MT7615BBPInit():BBP Initialization.....
  [   34.148000]  Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
  [   34.164000]  Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
  [   34.184000] MT7615BBPInit() todo
  [   34.192000] PHY Init Done!
  [   34.196000] tx_pwr_comp_init():NotSupportYet!
  [   34.208000] MtCmdSetMacTxRx:(ret = 0)
  [   34.212000] CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels
  [   34.232000] ApAutoChannelAtBootUp----------------->
  [   34.240000] MtCmdSetMacTxRx:(ret = 0)
  [   34.248000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210]  offset [1900]
  [   34.268000] MtCmdGetRXDCOCCalResult:(ret = 0)
  [   34.276000] mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98]
  [   34.296000] MtCmdGetTXDPDCalResult:(ret = 0)
  [   34.304000] MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0
  [   34.320000] BW = 2,TXStream = 4, RXStream = 4, scan(1)
  [   34.580000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210]  offset [1900]
  [   34.596000] MtCmdGetRXDCOCCalResult:(ret = 0)
  [   34.604000] mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98]
  [   34.624000] MtCmdGetTXDPDCalResult:(ret = 0)
  [   34.632000] MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0
  [   34.652000] BW = 2,TXStream = 4, RXStream = 4, scan(1)
  [   34.912000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210]  offset [1900]
  [   34.928000] MtCmdGetRXDCOCCalResult:(ret = 0)
  [   34.936000] mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98]
  [   34.956000] MtCmdGetTXDPDCalResult:(ret = 0)
  [   34.964000] MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0
  [   34.984000] BW = 2,TXStream = 4, RXStream = 4, scan(1)
  [   35.240000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210]  offset [1900]
  [   35.256000] MtCmdGetRXDCOCCalResult:(ret = 0)
  [   35.264000] mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98]
  [   35.284000] MtCmdGetTXDPDCalResult:(ret = 0)
  [   35.292000] MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0
  [   35.312000] BW = 2,TXStream = 4, RXStream = 4, scan(1)
  [   35.572000] ====================================================================
  [   35.584000] Channel  36 : Busy Time =    810, Skip Channel = FALSE, BwCap = TRUE
  [   35.600000] Channel  40 : Busy Time =    984, Skip Channel = FALSE, BwCap = TRUE
  [   35.616000] Channel  44 : Busy Time =   1120, Skip Channel = FALSE, BwCap = TRUE
  [   35.628000] Channel  48 : Busy Time =    698, Skip Channel = FALSE, BwCap = TRUE
  [   35.644000] ====================================================================
  [   35.660000] Rule 3 Channel Busy time value : Select Primary Channel 48
  [   35.672000] Rule 3 Channel Busy time value : Min Channel Busy = 1120
  [   35.684000] Rule 3 Channel Busy time value : BW = 80
  [   35.696000]  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 48
  [   35.716000]  AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 48
  [   35.736000]  AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 48
  [   35.756000]  AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 48
  [   35.776000] ApAutoChannelAtBootUp<-----------------
  [   35.784000] WifiSysOpen(), wdev idx = 0
  [   35.792000] wdev_attr_update(): wdevId0 = 50:41:b9:xx:xx:91
  [   35.804000] MtCmdSetDbdcCtrl:(ret = 0)
  [   35.812000] Current Channel is 48. DfsZeroWaitSupport=0
  [   35.824000] MtAsicSetChBusyStat(840): Not support for HIF_MT yet!
  [   35.836000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
  [   35.848000] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
  [   35.860000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=48
  [   35.876000] CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels
  [   35.892000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
  [   35.892000]  LinkToOmacIdx = 0, LinkToWdevType = 1
  [   35.924000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO),                 CmdBssInfoBmcRate.u2BcTransmit= 8192,                 CmdBssInfoBmcRate.u2McTransmit = 8192
  [   35.952000] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
  [   36.056000] [RadarStateCheck]Set into RD_NORMAL_MODE
  [   36.064000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn = 1
  [   36.076000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn = 1
  [   36.088000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn = 0
  [   36.096000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=48, HT-CentCh=46, VHT-CentCh=42
  [   36.112000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210]  offset [1900]
  [   36.132000] MtCmdGetRXDCOCCalResult:(ret = 0)
  [   36.140000] mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98]
  [   36.160000] MtCmdGetTXDPDCalResult:(ret = 0)
  [   36.168000] MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0
  [   36.188000] BW = 2,TXStream = 4, RXStream = 4, scan(0)
  [   36.292000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=48, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
  [   36.332000] [WrapDfsRadarDetectStart]: Band0Ch is 48[WrapDfsRadarDetectStart]: Band1Ch is 0MtAsicSetRalinkBurstMode(2593): Not support for HIF_MT yet!
  [   36.360000] MtAsicSetPiggyBack(777): Not support for HIF_MT yet!
  [   36.372000] MtAsicSetTxPreamble(2572): Not support for HIF_MT yet!
  [   36.384000] Main bssid = 50:41:b9:xx:xx:91
  [   36.392000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
  [   36.400000] MtCmdSetMacTxRx:(ret = 0)
  [   36.408000] MCS Set = ff ff ff ff 01
  [   36.416000] <==== mt_wifi_init, Status=0
  [   36.424000] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
  [   36.436000] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1
  [   36.452000] WtcSetMaxStaNum: MaxStaNum:88, BssidNum:4, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122
  [   36.512000] red_is_enabled: set CR4/N9 RED Enable to 1.
  [   36.524000] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
  [   36.536000] Correct apidx from 3 to 0 for WscUUIDInit
  [   36.544000] Generate UUID for apidx(0)
  [   36.552000] first MBSSID is 50 41 b9 xx xx 90
  [   36.560000] UUID: c3ab3540, len = 16
  [   36.568000] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 50 41 b9 xx xx 90
  [   36.580000]
  [   36.976000] device rai0 entered promiscuous mode
  [   36.984000] br-lan: port 3(rai0) entered forwarding state
  [   36.996000] br-lan: port 3(rai0) entered forwarding state
  [   37.292000] Device Instance
  [   37.296000]  WDEV 00:
  Name:rai0
  [   37.304000]          Wdev(list) Idx:0
  [   37.312000]           Idx:13
  [   37.316000]  WDEV 01:
  Name:rai1
  [   37.324000]          Wdev(list) Idx:1
  [   37.324000] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
  [   37.340000]           Idx:14
  [   37.344000]  WDEV 02:
  Name:rai2
  [   37.352000]          Wdev(list) Idx:2
  [   37.356000]           Idx:15
  [   37.360000]  WDEV 03:
  Name:rai3
  [   37.368000]          Wdev(list) Idx:3
  [   37.376000]           Idx:16
  [   37.380000]  WDEV 04:
  Name:apclii0
  [   37.388000]          Wdev(list) Idx:4
  [   37.392000]           Idx:17
  [   37.396000]  WDEV 05:
  [   37.400000]  WDEV 06:
  [   37.408000]  WDEV 07:
  [   37.412000]  WDEV 08:
  [   37.416000]  WDEV 09:
  [   37.420000]  WDEV 10:
  [   37.424000]  WDEV 11:
  [   37.428000]  WDEV 12:
  [   37.432000]  WDEV 13:
  [   37.436000]  WDEV 14:
  [   37.444000]  WDEV 15:
  [   37.448000]  WDEV 16:
  [   37.452000]  WDEV 17:
  [   39.000000] br-lan: port 3(rai0) entered forwarding state
  switch_val: 1
  ifce_automode: 0x01
  wan_link_stat: 0
  [   48.580000] led=9, on=4000, off=0, blinks,=0, reset=0, time=1 low_trigger=0
  [   62.188000] led=9, on=4000, off=0, blinks,=0, reset=0, time=1 low_trigger=0
  procd: - init complete -