ひたすらSGMIIを有効化できず手詰まりになっていたけど、QCA9558側とAR8327側の両方でSGMIIを構成する必要があることを最終的に突き止め、なんとかSGMIIのeth1も動作するところまで到達した
initramfs-factoryは当初WR8750NやWR9500Nなどと同様にtpブロックにinitramfsイメージ本体、firmware領域にダミー用のlzma-loaderを入れていたが、自然な形にする為にtpブロックにダミーなlzma-loader、firmware領域にinitramfsイメージとし、tpブロックが読みだされた場合は無限ループでWDTによりリセットさせることで、NECのブートローダにおける "SOFT-RESET" を発生させてtpのPOSTをスキップし、firmwareブロックのinitramfsイメージを読ませる形にした。
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
#### cwm_action_mac40to20: ht40 -> ht20
#### osif_vap_init: IEEE80211_F_COEXT_DISABLE skip wlan_determine_cw()
wmi_unified_vdev_stop_send
STOPPED EVENT for vap 0
stop wait 0
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Setting vdev param = 3, value = 100
Setting vdev param = 22, value = 3
ol_ath_vap_set_param: VAP param is now supported param:11 value:3
Notification to UMAC VAP layer
start wait 1
wmi_unified_vdev_stop_send
STOPPED EVENT for vap 0
stop wait 0
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
Setting vdev param = 3, value = 100
Setting vdev param = 22, value = 3
ol_ath_vap_set_param: VAP param is now supported param:11 value:3
Notification to UMAC VAP layer
start wait 1
wmi_unified_vdev_stop_send
STOPPED EVENT for vap 0
stop wait 0
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Setting vdev param = 3, value = 100
Setting vdev param = 22, value = 3
ol_ath_vap_set_param: VAP param is now supported param:11 value:3
Notification to UMAC VAP layer
start wait 1
wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xd30de0826610
Keyix=1 Keylen=16 Keyflags=1 Cipher=0
Keydata=0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
TXRX: sec spec for peer 0xc035e000 (10:66:82:e0:0d:d3): mcast key of type 0
FWLOG: [209566] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
wmi_unified_vdev_stop_send
STOPPED EVENT for vap 0
stop wait 0
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Setting vdev param = 3, value = 100
Setting vdev param = 22, value = 3
ol_ath_vap_set_param: VAP param is now supported param:11 value:3
Notification to UMAC VAP layer
start wait 1
vap_down 0
vap_down 0
DDR Activity - HIGH
vap_down 0
vap_down 0
wmi_unified_vdev_stop_send
beacon buffer av_wbuf is NULL - Ignoring SWBA event
STOPPED EVENT for vap 0
vap_down 1
NetBSD/scorpimips (Amnesiac) (console)
login: s/w clock, h/w clock diff
s/w real_time 1356966181 sec
h/w RTC 1356966184 sec
IPL:SOFT-RESET
memory test ... ok
flinstall OK
boot version: 1.0.0
PKG "2x2LIGHTNING"
CPU "Atheros/QCA9558"
Revision 113.0 CLOCK 720.0 MHz
HEAP MEMORY 262144 bytes
Boot:InitFilesystem
RGMII calibration GE0 ... ETH_CFG: 00028001 ETH_XMII: 5a000000
phy0.0: "Atheros/AR8327(phy)"
phy0.1: "Atheros/AR8327(SW)"
active ch:1
now booting Firmware ...
loaded Firmware
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 6.6.35 (musashino205@TAIHA.NET) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26434+140-0a861a0c0f) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Fri Jun 28 07:05:55 2024
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is NEC Aterm WG1400HP
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Kernel command line: rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 104372K/131072K available (6152K kernel code, 597K rwdata, 1424K rodata, 16968K init, 204K bss, 26700K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 720.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000001] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.092769] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.227751] pid_max: default: 32768 minimum: 301
[ 0.292867] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.380339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.481375] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.576626] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.694228] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.778078] pinctrl core: initialized pinctrl subsystem
[ 0.842737] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.931414] clocksource: Switched to clocksource MIPS
[ 1.002726] NET: Registered PF_INET protocol family
[ 1.061266] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.148456] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.249507] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.342140] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.433759] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 1.518137] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.594261] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.672380] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.756357] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.824138] PCI: CLS 0 bytes, default 32
[ 1.901588] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 1.980193] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.049973] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.379461] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 2.449092] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 2.556556] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.633572] printk: console [ttyS0] disabled
[ 2.685231] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 2.789343] printk: console [ttyS0] enabled
[ 2.789343] printk: console [ttyS0] enabled
[ 2.889326] printk: bootconsole [early0] disabled
[ 2.889326] printk: bootconsole [early0] disabled
[ 3.021170] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[ 3.082895] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.158945] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 3.238060] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 3.317436] Creating 4 MTD partitions on "spi0.0":
[ 3.374731] 0x000000000000-0x000000020000 : "bootloader"
[ 3.441336] 0x000000020000-0x000000030000 : "config"
[ 3.502786] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 3.582356] 0x000000030000-0x000000040000 : "art"
[ 3.640952] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 3.720392] 0x000000040000-0x000001000000 : "firmware"
[ 4.166651] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
[ 4.890897] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 5.015423] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 5.442289] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 5.550271] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[ 5.624598] i2c_dev: i2c /dev entries driver
[ 5.677932] NET: Registered PF_INET6 protocol family
[ 5.744500] Segment Routing with IPv6
[ 5.788357] In-situ OAM (IOAM) with IPv6
[ 5.835465] NET: Registered PF_PACKET protocol family
[ 5.895938] 8021q: 802.1Q VLAN Support v1.8
[ 5.962188] PCI host bridge to bus 0000:00
[ 6.011250] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 6.093472] pci_bus 0000:00: root bus resource [io 0x0000]
[ 6.160137] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 6.254940] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 6.326787] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x101fffff 64bit]
[ 6.408038] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 6.488327] pci 0000:00:00.0: supports D1
[ 6.536302] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 6.606420] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 6.685582] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 6.773039] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 6.860567] pca953x 0-0020: supply vcc not found, using dummy regulator
[ 6.940007] pca953x 0-0020: using no AI
[ 6.989073] i2c-gpio i2c: using lines 20 (SDA) and 19 (SCL)
[ 7.096382] clk: Disabling unused clocks
[ 7.205319] Freeing unusedrnel image (mem) memory: 68K
[ 7.266808] This architect does not haernel memory tection.
[ 7.332105] Run /init as process
[ 8.058489] init: Console alive
[ 8.096418] init: - watchd-
[ 8.130193] init: Watchdogs previouslyet the system[ 8.202854] kmodloader: long kernel mods from /etc/les-boot.d/*
[ 8.283477] usbcore: regised new inter driver usbfs[ 8.335936] usbcore: regied new interf driver hub
[ 8.391096] usbcore: regied new deviceiver usb
[ 8.449486] gpio_button_houg: loading of-tree modulaints kernel[ 8.527283] ehci-platform 00000.usb: EHost Controll
[ 8.584662] ehci-platform 00000.usb: nSB bus registd, assigned number 1
[ 8.663094] ehci-platform00000.usb: ir4, io mem 0x0000
[ 8.751434] ehci-platform 00000.usb: U.0 started, E 1.00
[ 8.816283] hub 1-0:1.0: Uhub found
[ 8.856192] hub 1-0:1.0: rt detected
[ 8.901628] kmodloader: doloading kerneodules from /modules-boot*
[ 8.985109] init: - preini
[ 9.231502] usb 1-1: new h-speed USB de number 2 us ehci-platfor[ 9.493183] hub 1-1:1.0: Uhub found
[ 9.554552] hub 1-1:1.0: 4rts detected[ 10.861449] random: crng i done
[ 12.530058] eth1: link up 00Mbps/Full ex)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 14.753527] eth1: link dow[ 14.800981] procd: - early
[ 14.832683] procd: - watch -
[ 14.867457] procd: Watchdoas previouslset the syste[ 15.487716] procd: - watch -
[ 15.522426] procd: Watchdoas previouslset the syste[ 15.575933] procd: - ubus[ 15.660091] procd: - init Please press Enter to activate this console.
[ 16.490822] kmodloader: long kernel mods from /etc/les.d/*
[ 17.608190] Loading moduleackported froinux version6.15-0-g51f3515c4
[ 17.684207] Backport generd by backporit 193becf2
[ 18.239665] PPP generic drr version 2.
[ 18.382495] NET: RegistereF_PPPOX prot family
[ 18.445744] urngd: v1.0.2 rted.
[ 18.584780] ath10k 6.7 dri, optimized CT firmware, bing pci dev 0x3c.
[ 18.774532] ath10k_pci 0000:00.0: pci legacy oper_imode 1 irq_m0 reset_mode [ 22.870965] ath10k_pci 0000:00.0: qca9hw2.0 target 100016c chip0x043222ff su000:0000
[ 22.962368] ath10k_pci 000:00.0: kconfdebug 0 debu1 tracing 0 d1 testmode 0[ 23.044581] ath10k_pci 0000:00.0: firm ver 10.1-ct-__fW-022-eca8 api 2 featu wmi-10.x,hai-mgmt-tx,mfpstatus-noack-10.x-CT,ratek-CT,txrate-et-temp-CT,tx-CT,cust-staT,retry-gt2-Cxrate2-CT,be-cb-CT,wmi-bl-ack-CT crc34cf97f
[ 23.980802] ath10k_pci 0000:00.0: boarle api 1 bmi_N/A crc32 be08
[ 25.008109] ath10k_pci 0000:00.0: 10.1 init: vdevs: peers: 127d: 256
[ 25.095012] ath10k_pci 0000:00.0: wmi t 'P 128 V 8 10'
[ 25.156714] ath10k_pci 0000:00.0: wmi t 'msdu-desc:24 sw-cryptct-sta: 0'
[ 25.235053] ath10k_pci 000:00.0: wmi pt 'alloc rem984 iram: 386
[ 25.356129] ath10k_pci 0000:00.0: htt-2.1 wmi-op 2 -op 2 cal nvmax-sta 128 r0 hwcrypto 1[ 25.447916] ath10k_pci 000:00.0: NOTE:irmware DBGLutput disablen debug_mask10000000
[ 25.795579] ieee80211 phy1theros AR955v:0 mem=0x8f03f, irq=16
[ 25.901850] kmodloader: doloading kernodules from //modules.d/*[ 47.500358] eth1: link up 00Mbps/Full ex)
[ 47.565636] br-lan: port 1h1.1) entereocking state
[ 47.617990] br-lan: port h1.1) enteredsabled state[ 47.673184] eth1.1: enterllmulticast m
[ 47.721775] ag71xx 1a00000th eth1: ent allmulticastde
[ 47.782451] eth1.1: entereromiscuous mo
[ 47.827241] ag71xx 1a00000th eth1: ent promiscuous e
[ 47.934749] br-lan: port 1h1.1) entereocking state
[ 47.987107] br-lan: port h1.1) enteredrwarding sta[ 48.145574] Atheros AR82168236/AR8316 .0:00: Port 1 up
[ 48.207473] Atheros AR82168236/AR8316 .0:00: Port 4 up
[ 48.270428] eth0: link up 00Mbps/Full dex)
BusyBox v1.36.1 (2024-06-28 07:05:55 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r26809+22-7c9644a7b5
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ls -al /tmp/
drwxrwxrwt 16 root root 420 Jun 28 07:08 .
drwxr-xr-x 1 root root 0 Jan 1 1970 ..
drwx------ 2 root root 160 Jun 28 07:06 .uci
---------- 1 root root 0 Jun 28 07:08 .ujailnoafile
-rw-r--r-- 1 root root 4 Jun 28 07:06 TZ
-rw-r--r-- 1 root root 924 Jan 1 1970 board.json
-rw-r--r-- 1 root root 0 Jun 28 07:06 dhcp.leases
drwxr-xr-x 2 root root 40 Jun 28 07:06 dnsmasq.d
drwxr-xr-x 3 root root 80 Jun 28 07:07 etc
drwxr-xr-x 2 root root 80 Jun 28 07:07 hosts
drwxr-xr-x 3 root root 60 Jun 28 07:06 lib
drwxrwxrwt 2 root root 400 Jun 28 07:08 lock
drwxr-xr-x 2 root root 80 Jun 28 07:05 log
-rw-r--r-- 1 root root 6816545 Jun 28 09:31 openwrt-ath79-generic-nec_wg1400hp-squashfs-sysupgrade.bin
-rw-r--r-- 1 root root 47 Jun 28 07:07 resolv.conf
drwxr-xr-x 2 root root 60 Jun 28 07:07 resolv.conf.d
drwxr-xr-x 4 root root 80 Jan 1 1970 root
drwxr-xr-x 7 root root 260 Jun 28 07:07 run
drwxrwxrwt 2 root root 40 Jun 28 07:06 shm
drwxr-xr-x 2 root root 80 Jun 28 09:35 state
drwxr-xr-x 2 root root 80 Jan 1 1970 sysinfo
drwxr-xr-x 2 root root 40 Jun 28 07:05 tmp
-rw-r--r-- 1 root root 129776 Jun 28 09:30 u-boot.bin
root@OpenWrt:/# mtd write /tmp/u-boot.bin bootloader
Unlocking bootloader ...
Writing from /tmp/u-boot.bin to bootloader ... [w]
root@OpenWrt:/# sysupgrade /tmp/openwrt-ath79-generic-nec_wg1400hp-squashfs-sysupgrade.bin
Cannot save config while running from ramdisk.
Fri Jun 28 09:31:30 UTC 2024 upgrade: Commencing upgrade. Closing all shell sessions.
Command failed: Connection faileWatchdog handover: fd=3
- watchdog -
Watchdog has previously reset the system
Fri Jun 28 09:31:31 UTC 2024 upgrade: Sending TERM to remaining processes ...
Fri Jun 28 09:31:36 UTC 2024 upgrade: Sending KILL to remaining processes ...
[ 174.814990] stage2 (3237):op_caches: 3Fri Jun 28 09:31:42 UTC 2024 upgrade: Switching to ramdisk...
Fri Jun 28 09:31:44 UTC 2024 upg[ 177.214845] do_stage2 (32 drop_caches:
rade: Performing system upgrade...
Unlocking firmware ...
Writing from <stdin> to firmware ... [w]
Appending jffs2 data from /tmp/sysupgrade.tgz to firmware..
.File /tmp/sysupgrade.tgz does not exist
Fri Jun 28 09:32:41 UTC 2024 upgrade: Upgrade completed
Fri Jun 28 09:32:42 UTC 2024 upg[ 235.669100] eboot: Restag system
"" *&+ ' " #' <--- U-Boot, シリアルコンソールのbaudrateが9600bpsから115200bpsに切り替わる
<--- 以下115200に切り替えた場合
U-Boot 2024.07-rc5+ (Jun 28 2024 - 16:12:50 +0900)
DRAM: 128 MiB
Core: 5 devices, 4 uclasses, devicetree: separate
Loading Environment from <NULL>... OK
In: uart@18020000
Out: uart@18020000
Err: uart@18020000
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-6.6.35
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 2543184 Bytes = 2.4 MiB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
Loading Kernel Image to 80060000
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 6.6.35 (musashino205@TAIHA.NET) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26434+140-0a861a0c0f) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Fri Jun 28 07:05:55 2024
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is NEC Aterm WG1400HP
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 120116K/131072K available (6152K kernel code, 597K rwdata, 1424K rodata, 1224K init, 204K bss, 10956K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 720.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000001] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008743] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.075720] pid_max: default: 32768 minimum: 301
[ 0.090768] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.098948] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.115939] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.128987] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.140000] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.150232] pinctrl core: initialized pinctrl subsystem
[ 0.158234] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.182517] clocksource: Switched to clocksource MIPS
[ 0.198984] NET: Registered PF_INET protocol family
[ 0.204700] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.213582] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.223065] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.231710] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.240274] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.248176] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.255405] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.262755] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.271239] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.277630] PCI: CLS 0 bytes, default 32
[ 0.286388] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.295127] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.301637] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.319243] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.326566] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.337714] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.345821] printk: console [ttyS0] disabled
[ 0.351094] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.360880] printk: console [ttyS0] enabled
[ 0.369790] printk: bootconsole [early0] disabled
[ 0.398848] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[ 0.404196] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.410675] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.417432] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.424416] Creating 4 MTD partitions on "spi0.0":
[ 0.429293] 0x000000000000-0x000000020000 : "bootloader"
[ 0.437636] 0x000000020000-0x000000030000 : "config"
[ 0.444666] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.451740] 0x000000030000-0x000000040000 : "art"
[ 0.458772] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.465830] 0x000000040000-0x000001000000 : "firmware"
[ 0.473402] 2 uimage-fw partitions found on MTD device firmware
[ 0.479425] Creating 2 MTD partitions on "firmware":
[ 0.484506] 0x000000000000-0x000000270000 : "kernel"
[ 0.491303] 0x000000270000-0x000000fc0000 : "rootfs"
[ 0.498080] mtd: setting mtd5 (rootfs) as root device
[ 0.503323] 1 squashfs-split partitions found on MTD device rootfs
[ 0.509640] 0x000000680000-0x000000fc0000 : "rootfs_data"
[ 0.868722] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
[ 1.521863] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 1.533066] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.874641] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.884463] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[ 1.891088] i2c_dev: i2c /dev entries driver
[ 1.895639] ath79-wdt 18060008.wdt: timeout value must be 0 < timeout < 14, using 14
[ 1.905628] NET: Registered PF_INET6 protocol family
[ 1.917592] Segment Routing with IPv6
[ 1.921406] In-situ OAM (IOAM) with IPv6
[ 1.925608] NET: Registered PF_PACKET protocol family
[ 1.930787] 8021q: 802.1Q VLAN Support v1.8
[ 1.960950] PCI host bridge to bus 0000:00
[ 1.965150] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 1.972131] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.977810] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.985899] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 1.992031] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.998979] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.005866] pci 0000:00:00.0: supports D1
[ 2.009936] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.017161] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.023947] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 2.031390] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 2.039837] pca953x 0-0020: supply vcc not found, using dummy regulator
[ 2.046848] pca953x 0-0020: using no AI
[ 2.053902] i2c-gpio i2c: using lines 20 (SDA) and 19 (SCL)
[ 2.099271] clk: Disabling unused clocks
[ 2.112801] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.124299] Freeing unused kernel image (initmem) memory: 1224K
[ 2.130320] This architecture does not have kernel memory protection.
[ 2.136883] Run /sbin/init as init process
[ 2.141036] with arguments:
[ 2.141040] /sbin/init
[ 2.141046] with environment:
[ 2.141051] HOME=/
[ 2.141056] TERM=linux
[ 2.904496] init: Console is alive
[ 2.908299] init: - watchdog -
[ 4.437218] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.525939] usbcore: registered new interface driver usbfs
[ 4.531647] usbcore: registered new interface driver hub
[ 4.537158] usbcore: registered new device driver usb
[ 4.546350] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 4.566209] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.571986] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.580129] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000
[ 4.612537] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.620068] hub 1-0:1.0: USB hub found
[ 4.624491] hub 1-0:1.0: 1 port detected
[ 4.633593] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.651690] init: - preinit -
[ 5.000880] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 5.487093] hub 1-1:1.0: USB hub found
[ 5.491282] hub 1-1:1.0: 4 ports detected
[ 7.832552] random: crng init done
[ 9.930276] eth1: link up (1000Mbps/Full duplex)
[ 12.178555] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 12.189415] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.256474] eth1: link down
[ 12.284775] procd: - early -
[ 12.287996] procd: - watchdog -
[ 13.000462] procd: - watchdog -
[ 13.004544] procd: - ubus -
[ 13.169439] procd: - init -
[ 14.767594] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.813486] Loading modules backported from Linux version v6.6.15-0-g51f354b815c4
[ 15.821095] Backport generated by backports.git 193becf2
[ 16.708733] PPP generic driver version 2.4.2
[ 16.733650] NET: Registered PF_PPPOX protocol family
[ 16.785643] urngd: v1.0.2 started.
[ 16.819649] ath10k 6.7 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 16.873373] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 16.879896] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 21.098530] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[ 21.107952] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 21.119956] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 22.029326] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 22.986367] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 23.003794] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 23.010125] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 23.018289] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 23.086991] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal nvmem max-sta 128 raw 0 hwcrypto 1
[ 23.097188] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 23.236435] ath: EEPROM regdomain: 0x88
[ 23.236457] ath: EEPROM indicates we should expect a direct regpair map
[ 23.236470] ath: Country alpha2 being used: JP
[ 23.236478] ath: Regpair used: 0x88
[ 23.329321] ath: EEPROM regdomain: 0x88
[ 23.329345] ath: EEPROM indicates we should expect a direct regpair map
[ 23.329359] ath: Country alpha2 being used: JP
[ 23.329366] ath: Regpair used: 0x88
[ 23.346571] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 23.347433] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xd27f7618, irq=16
[ 23.390289] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 84.590602] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 84.642618] jffs2_build_filesystem(): unlocking the mtd device...
[ 84.642665] done.
[ 84.650880] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 86.055378] eth1: link up (1000Mbps/Full duplex)
[ 86.077297] br-lan: port 1(eth1.1) entered blocking state
[ 86.082849] br-lan: port 1(eth1.1) entered disabled state
[ 86.088356] eth1.1: entered allmulticast mode
[ 86.092804] ag71xx 1a000000.eth eth1: entered allmulticast mode
[ 86.099045] eth1.1: entered promiscuous mode
[ 86.103424] ag71xx 1a000000.eth eth1: entered promiscuous mode
[ 86.165198] br-lan: port 1(eth1.1) entered blocking state
[ 86.170724] br-lan: port 1(eth1.1) entered forwarding state
[ 86.321626] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 1 is up
[ 86.328196] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 4 is up
[ 86.335823] eth0: link up (1000Mbps/Full duplex)
[ 143.328789] done.
[ 143.330773] jffs2: notice: (2273) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 143.532274] overlayfs: upper fs does not support tmpfile.
BusyBox v1.36.1 (2024-06-28 07:05:55 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r26809+22-7c9644a7b5
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ubus call system board
{
"kernel": "6.6.35",
"hostname": "OpenWrt",
"system": "Qualcomm Atheros QCA9558 ver 1 rev 0",
"model": "NEC Aterm WG1400HP",
"board_name": "nec,wg1400hp",
"rootfs_type": "squashfs",
"release": {
"distribution": "OpenWrt",
"version": "SNAPSHOT",
"revision": "r26809+22-7c9644a7b5",
"target": "ath79/generic",
"description": "OpenWrt SNAPSHOT r26809+22-7c9644a7b5"
}
}
root@OpenWrt:/# ubus call system info
{
"localtime": 1719567425,
"uptime": 256,
"load": [
14400,
28960,
14176
],
"memory": {
"total": 124252160,
"free": 78188544,
"shared": 258048,
"buffered": 0,
"available": 65454080,
"cached": 23220224
},
"root": {
"total": 9472,
"free": 9052,
"used": 420,
"avail": 9052
},
"tmp": {
"total": 60668,
"free": 60464,
"used": 204,
"avail": 60464
},
"swap": {
"total": 0,
"free": 0
}
}
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 4.3M 4.3M 0 100% /rom
tmpfs 59.2M 204.0K 59.0M 0% /tmp
tmpfs 59.2M 48.0K 59.2M 0% /tmp/root
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock6 9.3M 420.0K 8.8M 4% /overlay
overlayfs:/overlay 9.3M 420.0K 8.8M 4% /
root@OpenWrt:/#
